Hello
The boot information is as below.

Linux version 2.6.11.6PNX8550 (root@slx) (gcc version 3.3.4) #79 Tue Jun 13 13:6
CPU revision is: 00061200
Determined physical RAM map:
memory: 03800000 @ 00000000 (usable)
Built 1 zonelists
Kernel command line: root=/dev/nfs nfsroot=192.168.0.1:/home/stb810-SP2/build/r0
Primary instruction cache 16kB, physically tagged, 2-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (34 instructions).
Synthesized TLB load handler fastpath (31 instructions).
Synthesized TLB store handler fastpath (31 instructions).
Synthesized TLB modify handler fastpath (30 instructions).
PID hash table entries: 256 (order: 8, 4096 bytes)
Using 250.710 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 52004k/57344k available (3219k kernel code, 5272k reserved, 856k data, )
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
Can't analyze prologue code at 80382f44
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PNX8550 PCI fixup vendor 10ec, device 8139 REALTEK 8139 Ethernet Card [irq = 25]
NTFS driver 2.1.22 [Flags: R/O].
JFFS version 1.0, (C) 1999, 2000 Axis Communications AB
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
8139too Fast Ethernet driver 0.9.27
PCI: Enabling device 0000:00:0a.0 (0000 -> 0003)
eth0: RealTek RTL8139 at 0xc005e100, 00:e0:4c:77:23:0a, IRQ 55
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
HPT371: IDE controller at PCI slot 0000:00:08.0
PCI: Enabling device 0000:00:08.0 (0000 -> 0003)
HPT371: chipset revision 2
CPU 0 Unable to handle kernel paging request at virtual address c6001022, epc =4
Oops in arch/mips/mm/fault.c::do_page_fault, line 166[#1]:
Cpu 0
$ 0 : 00000000 10008400 c6001022 a0000000
$ 4 : 26001028 803cb4d0 a0000000 a0000000
$ 8 : 804c5ab8 00000008 00000000 00000000
$12 : fffffffb ffffffff 0000000a 00000000
$16 : 26001000 804a7000 00000000 804299a4
$20 : 804a7000 804c5eb8 00000000 00000000
$24 : 804c5d38 80484c4b
$28 : 804c4000 804c5e10 00000000 8025d9d4
Hi : 00000000
Lo : 00000000
epc : 8025d9ec init_hpt37x+0x74/0x50c Not tainted
ra : 8025d9d4 init_hpt37x+0x5c/0x50c
Status: 10008403 KERNEL EXL IE
Cause : 30800008
BadVA : c6001022
PrId : 00061200
Modules linked in:
Process swapper (pid: 1, threadinfo=804c4000, task=804abb78)
Stack : 801f2dac 00000001 804c5e80 804c5eb8 00000007 800823d0 804a7000 804c5e58
00000008 804299a4 804a7000 804c5eb8 8025e090 8025e080 00000002 a0000000
00000003 00000002 80429b08 00000001 00000000 00000001 00000037 8026cbd4
fffc0000 00000000 00000002 803ecc9c 00000000 8048cd10 80429b10 804a7000
804299a4 00000000 00000000 00000000 8026cc68 00000000 804c5eb0 80484c4b
...
Call Trace:
[<801f2dac>] pci_bus_read_config_byte+0x4c/0x8c
[<800823d0>] printk+0x1c/0x28
[<8025e090>] init_chipset_hpt366+0x10c/0x164
[<8025e080>] init_chipset_hpt366+0xfc/0x164
[<8026cbd4>] do_ide_setup_pci_device+0x130/0x1a0
[<8026cc68>] ide_setup_pci_device+0x24/0xd0
[<8025e750>] init_setup_hpt37x+0x10/0x1c
[<801e48c0>] idr_get_new+0x18/0x4c
[<8025e970>] hpt366_init_one+0x30/0x3c
[<8047794c>] ide_scan_pcidev+0x98/0xb0
[<801f7e3c>] pci_find_device+0x1c/0x28
[<8011a630>] proc_register+0x1c/0xfc
[<804779b0>] ide_scan_pcibus+0x4c/0xf4
[<8011aa98>] proc_mkdir_mode+0x54/0x80
[<8011aa6c>] proc_mkdir_mode+0x28/0x80
[<80477828>] probe_for_hwifs+0x18/0x24
[<8011aad8>] proc_mkdir+0x14/0x20
[<80477898>] ide_init+0x64/0x80
[<80476c6c>] init_dvbdev+0x20/0xec
[<8045c8cc>] do_initcalls+0x50/0x108
[<8045c8cc>] do_initcalls+0x50/0x108
[<80478f08>] sock_init+0x34/0x50
[<8046e298>] sysctl_init+0x28/0x34
[<8045c9bc>] do_basic_setup+0x38/0x44
[<800604e4>] init+0x3c/0x118
[<800604dc>] init+0x34/0x118
[<80062f9c>] kernel_thread_helper+0x10/0x18
[<80062f8c>] kernel_thread_helper+0x0/0x18

Code: 8c6384d0 26040028 00621021 <90450000> 00641821 90640000 30a500ff 240
Kernel panic - not syncing: Attempted to kill init!

Thanks!