How do I get the kernel to recognize 8GB of RAM? It is only recognizing
3.3GB?

Also, where do I go for packages for 4.5 current? The install.amd64
file reference ftp://ftp.openbsd.org/pub/OpenBSD/4.5/amd64 but no such
ftp exists.

-Dave

dmesg below:
ing; disabled or no drives?)
ppb3 at pci0 dev 28 function 5 "Intel 82801JI PCIE" rev 0x00: apic 4
int 16 (irq 10)
pci4 at ppb3 bus 2
mskc0 at pci4 dev 0 function 0 "Marvell Yukon 88E8056" rev 0x12,
Yukon-2 EC Ultra (0x3): apic 4 int 17 (irq 11)
msk0 at mskc0 port A: address 00:22:15:9c:87:7e
eephy0 at msk0 phy 0: 88E1149 Gigabit PHY, rev. 1
uhci3 at pci0 dev 29 function 0 "Intel 82801JI USB" rev 0x00: apic 4
int 23 (irq 7)
uhci4 at pci0 dev 29 function 1 "Intel 82801JI USB" rev 0x00: apic 4
int 19 (irq 5)
uhci5 at pci0 dev 29 function 2 "Intel 82801JI USB" rev 0x00: apic 4
int 18 (irq 15)
ehci1 at pci0 dev 29 function 7 "Intel 82801JI USB" rev 0x00: apic 4
int 23 (irq 7)
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb4 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x90
pci5 at ppb4 bus 5
skc0 at pci5 dev 2 function 0 "Marvell Yukon 88E8001/8003/8010" rev
0x14, Yukon Lite (0x9): apic 4 int 18 (irq 15)
sk0 at skc0 port A: address 00:22:15:9c:9d:b7
eephy1 at sk0 phy 0: 88E1011 Gigabit PHY, rev. 5
"AT&T/Lucent FW322 1394" rev 0x70 at pci5 dev 3 function 0 not configured
pcib0 at pci0 dev 31 function 0 "Intel 82801JIR LPC" rev 0x00
pciide1 at pci0 dev 31 function 2 "Intel 82801JI SATA" rev 0x00: DMA
(unsupported), channel 0 configured to native-PCI, channel 1
configured to native-PCI
pciide1: using apic 4 int 19 (irq 5) for native-PCI interrupt
pciide1: channel 0 ignored (not responding; disabled or no drives?)
atapiscsi0 at pciide1 channel 1 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TSSTcorp, CDDVDW SH-S223Q, SB02> ATAPI
5/cdrom removable
ichiic0 at pci0 dev 31 function 3 "Intel 82801JI SMBus" rev 0x00: apic
4 int 18 (irq 15)
iic0 at ...
[ message continues ]

There is no 4.5.  If you're running a snapshot, the sets and packages
are in the snapshots directory.

[ message continues ]