> -----Original Message-----
> From:
owner-misc@openbsd.org [mailto:owner-misc@openbsd.org]
> On Behalf Of Emilio Perea
> Sent: Sunday, August 03, 2008 6:29 AM
> To:
misc@openbsd.org
> Subject: Problem with current i386 snapshot
>
> This build seems to go into an endless reboot cycle, rebooting before
> anything shows up in the console of a Soekris net4801. The previous
> snapshot (build #1004) works fine. Unfortunately I have
> nothing to show
> for it as far as filing a proper bug report. BIOS screen followed by
> the changing console to com0 message followed by the BIOS screen etc.
>
> Problem build:
> OpenBSD 4.4-beta (GENERIC) #1010: Sat Aug 2 12:39:46 MDT 2008
> deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
>
> Last working version dmesg:
> OpenBSD 4.4-beta (GENERIC) #1004: Thu Jul 31 00:42:16 MDT 2008
> deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
> cpu0: Geode(TM) Integrated Processor by National Semi ("Geode
> by NSC" 586-class) 267 MHz
> cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
> cpu0: TSC disabled
> real mem = 133787648 (127MB)
> avail mem = 120946688 (115MB)
> mainbus0 at root
> bios0 at mainbus0: AT/286+ BIOS, date 20/80/03, BIOS32 rev. 0
> @ 0xf7840
> pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
> pcibios0: pcibios_get_intr_routing - function not supported
> pcibios0: PCI IRQ Routing information unavailable.
> pcibios0: PCI bus #0 is the last bus
> bios0: ROM list: 0xc8000/0x9000
> cpu0 at mainbus0
> pci0 at mainbus0 bus 0: configuration mode 1 (bios)
> pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00
> sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00,
> DP83816A: irq 10, address 00:00:24:c2:9e:30
> nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
> sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00,
> DP83816A: irq 10, address 00:00:24:c2:9e:31
> nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
> sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00,
> DP83816A: irq 10, address 00:00:24:c2:9e:32
> nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1
> gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
> gpio0 at gscpcib0: 64 pins
> "NS SC1100 SMI" rev 0x00 at pci0 dev 18 function 1 not configured
> pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01:
> DMA, channel 0 wired to compatibility, channel 1 wired to
> compatibility
> wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFX-2048>
> wd0: 4-sector PIO, LBA, 1953MB, 4001760 sectors
> wd0(pciide0:0:0): using PIO mode 4
> geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev
> 0x00: iid 6 revision 3 wdstatus 0
> ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev
> 0x08: irq 11, version 1.0, legacy support
> isa0 at gscpcib0
> isadma0 at isa0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> com0: console
> com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: <PC speaker>
> spkr0 at pcppi0
> nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
> gpio1 at nsclpcsio0: 29 pins
> gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1:
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> usb0 at ohci0: USB revision 1.0
> uhub0 at usb0 "Compaq OHCI root hub" rev 1.00/1.00 addr 1
> biomask fbe5 netmask ffe5 ttymask ffff
> softraid0 at root
> root on wd0a swap on wd0b dump on wd0b
