On Wed, Jul 09, 2008 at 06:52:44PM +0700, riwanlky wrote:
> I want my OpenBSD 4.3 to get clock from my serial GPS device.

quoted text
>

> The device is working

> # cu -l /dev/cua00 -s 4800

> Connected

> $GPRMC,113516.000,A,0608.4965,S,10651.2976,E,0.07,229.06,090708,,,A*75

> $GPRMC,113517.000,A,0608.4964,S,10651.2975,E,0.04,193.07,090708,,,A*76

> $GPRMC,113518.000,A,0608.4963,S,10651.2974,E,0.07,144.19,090708,,,A*79

> $GPRMC,113519.000,A,0608.4962,S,10651.2974,E,0.06,159.34,090708,,,A*7B

> $GPRMC,113520.000,A,0608.4962,S,10651.2974,E,0.08,246.72,090708,,,A*70

> $GPRMC,113521.000,A,0608.4961,S,10651.2973,E,0.07,231.23,090708,,,A*7E

> $GPRMC,113522.000,A,0608.4960,S,10651.2973,E,0.16,129.40,090708,,,A*73

>

> then

> # ldattach -s 4800 nmea /dev/cua00

> # sysctl hw.sensors

> hw.sensors.lm1.temp0=72.00 degC

> hw.sensors.lm1.temp1=61.50 degC

> hw.sensors.lm1.temp2=59.00 degC

> hw.sensors.lm1.volt0=1.23 VDC (VCore A)

> hw.sensors.lm1.volt1=2.58 VDC (VCore B)

> hw.sensors.lm1.volt2=3.33 VDC (+3.3V)

> hw.sensors.lm1.volt3=4.97 VDC (+5V)

> hw.sensors.lm1.volt4=0.00 VDC (+12V)

> hw.sensors.lm1.volt5=-14.91 VDC (-12V)

> hw.sensors.lm1.volt6=-7.71 VDC (-5V)

> hw.sensors.lm1.volt7=4.97 VDC (5VSB)

> hw.sensors.lm1.volt8=0.58 VDC (VBAT)

> hw.sensors.nmea0.timedelta0=25024.555114 secs (GPS autonomous), OK, Thu

> Jul 10 01:35:50.555

>

> so the device is working, however when I do ntpd

> # ntpd -ds

> listening on 127.0.0.1

> listening on ::1

> listening on fe80:4::1

> listening on 192.168.1.200

> listening on fe80:1::20d:b9ff:fe0c:d404

> listening on 192.168.3.200

> listening on fe80:2::20b:6bff:fe87:6739

> ntp engine ready

> no reply received in time, skipping initial time setting

> 0 out of 1 peers valid

> bad peer nmea0 (not resolved)

>

> my ntpd.conf

> # cat /etc/ntpd.conf

> # $OpenBSD: ntpd.conf,v 1.8 2007/07/13 09:05:52 henning Exp $

> # sample ntpd configuration file, see ntpd.conf(5)

>

> # Addresses to listen on (ntpd does not listen by default)

> listen on *

>

> # sync to a single server

> #server ntp.example.org

> server nmea0

server != sensor
See man ntpd.conf
	-Otto