Goodmorning,
During boot my AMD64 machine with RAID setup shows me the following
messages:
raidctl: ioctl RAIDFRAME_CONFIGURE failed
raid0: Device already configured!
I have followed the instructions over at:
http://www.eclectica.ca/howto/openbsd-software-raid-howto.php.
Kernel additions to GENERIC are:
option RAID_AUTOCONFIG
pseudo-device raid 4
'raidctl -s' shows everything *seems* to be fine; I am not sure why I
get the error and warning.
I also noticed the writing to disk is rather slow compared to IDE disks
on other machines; or so it seems.
All this makes me concerned the install is not correct / trustworthy.
Any advice is highly appreciated, please let me know if I should supply
other info than that below.
Thanks!
------------------
# raidctl -s raid0
raid0 Components:
/dev/wd0d: optimal
/dev/wd1d: optimal
No spares.
Parity status: clean
Reconstruction is 100% complete.
Parity Re-write is 100% complete.
Copyback is 100% complete.
----------------
# cat /etc/raid0.conf
START array
1 2 0
START disks
/dev/wd0d
/dev/wd1d
START layout
128 1 1 1
START queue
fifo 100
----------------
# cat /etc/fstab
/dev/raid0a / ffs rw 1 1
/dev/raid0g /home ffs rw,nodev,nosuid 1 2
/dev/raid0e /tmp ffs rw,nodev,nosuid 1 2
/dev/raid0d /usr ffs rw,nodev 1 2
/dev/raid0f /var ffs rw,nodev,nosuid 1 2
----------------
# dmesg
OpenBSD 4.1 (GENERIC.RAID) #0: Tue Jun 5 18:30:18 CEST 2007
root@mybox.xyz:/usr/src/sys/arch/amd64/compile/GENERIC.RAID
real mem = 1072164864 (1047036K)
avail mem = 906080256 (884844K)
using 22937 buffers containing 107425792 bytes (104908K) of memory
mainbus0 (root)
bios0 at mainbus0: SMBIOS rev. 2.3 @ 0xf0000 (40 entries)
bios0: Sun Microsystems Sun Fire(TM) X2100
acpi at mainbus0 not configured
cpu0 at mainbus0: (uniprocessor)
cpu0: AMD Opteron(tm) Processor 150, 2412.65 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,SSE3,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW
cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 1MB
64b/line 16-way L2 cache
cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: Cool'n'Quiet K8 2412 MHz: speeds: 2400 2200 2000 1800 1000 MHz
cpu0: AMD erratum 89 present, BIOS upgrade may be required
pci0 at mainbus0 bus 0: configuration mode 1
"NVIDIA nForce4 DDR" rev 0xa3 at pci0 dev 0 function 0 not configured
pcib0 at pci0 dev 1 function 0 "NVIDIA nForce4 ISA" rev 0xa3
nviic0 at pci0 dev 1 function 1 "NVIDIA nForce4 SMBus" rev 0xa2
iic0 at nviic0
adt0 at iic0 addr 0x2e: sch5017 rev 0x89
iic1 at nviic0
adt1 at iic1 addr 0x2e: sch5017 rev 0x89
ohci0 at pci0 dev 2 function 0 "NVIDIA nForce4 USB" rev 0xa2: irq 11,
version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: NVIDIA OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 8 ports with 8 removable, self powered
ehci0 at pci0 dev 2 function 1 "NVIDIA nForce4 USB" rev 0xa3: irq 3
usb1 at ehci0: USB revision 2.0
uhub1 at usb1
uhub1: NVIDIA EHCI root hub, rev 2.00/1.00, addr 1
uhub1: 8 ports with 8 removable, self powered
pciide0 at pci0 dev 6 function 0 "NVIDIA nForce4 IDE" rev 0xf2: DMA,
channel 0 configured to compatibility, channel 1 configured to compatibility
pciide0: channel 0 disabled (no drives)
pciide0: channel 1 disabled (no drives)
pciide1 at pci0 dev 7 function 0 "NVIDIA nForce4 SATA" rev 0xf3: DMA
pciide1: using irq 10 for native-PCI interrupt
wd0 at pciide1 channel 0 drive 0:
wd0: 16-sector PIO, LBA48, 114473MB, 234441648 sectors
wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
wd1 at pciide1 channel 1 drive 0:
wd1: 16-sector PIO, LBA48, 114473MB, 234441648 sectors
wd1(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 5
pciide2 at pci0 dev 8 function 0 "NVIDIA nForce4 SATA" rev 0xf3: DMA
pciide2: using irq 11 for native-PCI interrupt
ppb0 at pci0 dev 9 function 0 "NVIDIA nForce4 PCI-PCI" rev 0xa2
pci1 at ppb0 bus 1
vga1 at pci1 dev 5 function 0 "ATI Rage XL" rev 0x27
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ppb1 at pci0 dev 11 function 0 "NVIDIA nForce4 PCIE" rev 0xa3
pci2 at ppb1 bus 2
ppb2 at pci0 dev 12 function 0 "NVIDIA nForce4 PCIE" rev 0xa3
pci3 at ppb2 bus 3
ppb3 at pci0 dev 13 function 0 "NVIDIA nForce4 PCIE" rev 0xa3
pci4 at ppb3 bus 4
bge0 at pci4 dev 0 function 0 "Broadcom BCM5721" rev 0x11, BCM5750 B1
(0x4101): irq 5, address 00:e0:81:59:6d:eb
brgphy0 at bge0 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0
ppb4 at pci0 dev 14 function 0 "NVIDIA nForce4 PCIE" rev 0xa3
pci5 at ppb4 bus 5
pchb0 at pci0 dev 24 function 0 "AMD AMD64 HyperTransport" rev 0x00
pchb1 at pci0 dev 24 function 1 "AMD AMD64 Address Map" rev 0x00
pchb2 at pci0 dev 24 function 2 "AMD AMD64 DRAM Cfg" rev 0x00
pchb3 at pci0 dev 24 function 3 "AMD AMD64 Misc Cfg" rev 0x00
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0:
spkr0 at pcppi0
Kernelized RAIDframe activated
raid0 (root): (RAID Level 1) total number of sectors is 232338816
(113446 MB) as root
umass0 at uhub1 port 1 configuration 1 interface 0
umass0: PHILIPS SPD3000CC, rev 2.00/2.40, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets
cd0 at scsibus0 targ 1 lun 0: SCSI0 5/cdrom
removable
uhidev0 at uhub0 port 5 configuration 1 interface 0
uhidev0: Logitech Logitech USB Keyboard, rev 1.10/15.00, addr 2, iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub0 port 5 configuration 1 interface 1
uhidev1: Logitech Logitech USB Keyboard, rev 1.10/15.00, addr 2, iclass 3/0
uhidev1: 3 report ids
uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
ums0 at uhidev1 reportid 3: 0 buttons and Z dir.
wsmouse0 at ums0 mux 0
dkcsum: wd0 matches BIOS drive 0x80
dkcsum: wd1 matches BIOS drive 0x81
swapmount: no device
raid0: Device already configured!
