Hi,

We run quite fine here with 4.2-current from today on a DL320G5, after:

enabling write cache in the HP Bios !
enabling amd64 bsd.mp
enabling acpi
enabling write cache for wd0 in the system with:

# atactl wd0 writecacheenable

Before we had horrible 2MByte write speed, now we have 67MByte.

The bge interfaces also seem to run fine.

cheers Kai

manam:~ # dmesg
OpenBSD 4.2-current (GENERIC.MP) #1436: Mon Oct 29 23:01:38 MDT 2007
     deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 2145415168 (2046MB)
avail mem = 2071965696 (1975MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.3 @ 0xee000 (47 entries)
bios0: vendor HP version "W04" date 03/10/2007
bios0: HP ProLiant DL320 G5
acpi0 at mainbus0: rev 2
acpi0: tables DSDT FACP SPCR MCFG HPET SPMI APIC
acpitimer at acpi0 not configured
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Xeon(R) CPU 3040 @ 1.86GHz, 1866.98 MHz
cpu0: 
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,CX16,xTPR,LONG
cpu0: 2MB 64b/line 8-way L2 cache
cpu0: apic clock running at 266MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Xeon(R) CPU 3040 @ 1.86GHz, 1866.74 MHz
cpu1: 
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,CX16,xTPR,LONG
cpu1: 2MB 64b/line 8-way L2 cache
ioapic0 at mainbus0 apid 8 pa 0xfec00000, version 20, 24 pins
acpiprt0 at acpi0: bus 1 (IP2P)
acpiprt1 at acpi0: bus 4 (PCXS)
acpiprt2 at acpi0: bus 3 (PCXA)
acpiprt3 at acpi0: bus 2 (ICHE)
acpiprt3: no apic found for irq 47
acpiprt4 at acpi0: bus 7 (IPE4)
acpiprt5 at acpi0: bus 10 (PTA0)
acpiprt6 at acpi0: bus 0 (PCI0)
acpicpu at acpi0 not configured
acpicpu at acpi0 not configured
acpicpu at acpi0 not configured
acpicpu at acpi0 not configured
acpicpu at acpi0 not configured
acpicpu at acpi0 not configured
acpicpu at acpi0 not configured
acpicpu at acpi0 not configured
acpitz at acpi0 not configured
ipmi0 at mainbus0: version 2.0 interface KCS iobase 0xca2/2 spacing 1
pci0 at mainbus0 bus 0: configuration mode 1
pchb0 at pci0 dev 0 function 0 "Intel E7230 MCH" rev 0xc0
ppb0 at pci0 dev 1 function 0 "Intel E7230 PCIE" rev 0xc0
pci1 at ppb0 bus 10
ppb1 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01
pci2 at ppb1 bus 2
ppb2 at pci2 dev 0 function 0 "ServerWorks PCIE-PCIX" rev 0xb5
pci3 at ppb2 bus 3
bge0 at pci3 dev 4 function 0 "Broadcom BCM5714" rev 0xa3, BCM5715 A3 
(0x9003): apic 8 int 16 (irq 11), address 00:1b:78:7a:c8:68
brgphy0 at bge0 phy 1: BCM5714 10/100/1000baseT PHY, rev. 0
bge1 at pci3 dev 4 function 1 "Broadcom BCM5714" rev 0xa3, BCM5715 A3 
(0x9003): apic 8 int 17 (irq 10), address 00:1b:78:7a:c8:69
brgphy1 at bge1 phy 1: BCM5714 10/100/1000baseT PHY, rev. 0
ppb3 at pci3 dev 8 function 0 "ServerWorks HT-1000 PCIX" rev 0xb4
pci4 at ppb3 bus 4
ppb4 at pci0 dev 28 function 4 "Intel 82801G PCIE" rev 0x01
pci5 at ppb4 bus 7
ppb5 at pci0 dev 28 function 5 "Intel 82801G PCIE" rev 0x01
ppb5: not configured by system firmware
uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x01: apic 8 int 
21 (irq 5)
uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x01: apic 8 int 
21 (irq 5)
uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x01: apic 8 int 
21 (irq 5)
uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x01: apic 8 int 
21 (irq 5)
ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x01: apic 8 int 
21 (irq 5)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb6 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0xe1
pci6 at ppb6 bus 1
vga1 at pci6 dev 3 function 0 "ATI ES1000" rev 0x02
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
"Compaq iLO" rev 0x03 at pci6 dev 4 function 0 not configured
"Compaq iLO" rev 0x03 at pci6 dev 4 function 2 not configured
uhci4 at pci6 dev 4 function 4 "Hewlett-Packard USB" rev 0x00: apic 8 
int 23 (irq 11)
"Hewlett-Packard IPMI" rev 0x00 at pci6 dev 4 function 6 not configured
usb1 at uhci4: USB revision 1.0
uhub1 at usb1 "Hewlett-Packard UHCI root hub" rev 1.00/1.00 addr 1
pcib0 at pci0 dev 31 function 0 "Intel 82801GB LPC" rev 0x01
pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev 0x01: DMA, 
channel 0 configured to compatibility, channel 1 configured to compatibility
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TEAC, DV-28E-N, C.6B> SCSI0 5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
pciide1 at pci0 dev 31 function 2 "Intel 82801GB SATA" rev 0x01: DMA, 
channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide1: using apic 8 int 20 (irq 7) for native-PCI interrupt
wd0 at pciide1 channel 0 drive 0: <ST3808110AS>
wd0: 16-sector PIO, LBA48, 76319MB, 156301488 sectors
wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
com1: probed fifo depth: 0 bytes
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
uhidev0 at uhub1 port 1 configuration 1 interface 0 "HP Virtual 
Keyboard" rev 1.10/0.02 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes, country code 33
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub1 port 1 configuration 1 interface 1 "HP Virtual 
Keyboard" rev 1.10/0.02 addr 2
uhidev1: iclass 3/1
ums0 at uhidev1: 3 buttons
wsmouse0 at ums0 mux 0
uhub6 at uhub1 port 2 "HP Virtual Hub" rev 1.10/0.01 addr 3
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a swap on wd0b dump on wd0b


quoted text
> Hello evo,
> 
> Wednesday, October 24, 2007, 12:51:13 AM, you wrote:
> 
> e> I'm choosing firewall/proxy/mail-gateway hardware running (of course)
> e> OpenBSD for medium office and my shortlist is:
> e> (a) HP ProLiant DL320 and (b) Sun Fire V125
> 
>   I'm   upgrading   my  servers/firewalls  to HP ProLiant DL320 G5, and the
> experience...  isn't  easy.  First  of  all you need to allow acpi in an MP
> kernel,  otherwise it's slow and unstable (it's disabled by default and not
> really documented).
> 
>   Then you have couple more issues I couldn't resolve yet:
> 
>   Fists - uhci (uhci4 in my case) giving an error during boot and shutdown:
> 
> OpenBSD 4.2-stable (GENERIC) #1: Thu Oct 18 12:35:10 CDT 2007
>     root@build.twopoint.com:/usr/src/sys/arch/i386/compile/GENERIC
> cpu0: Intel(R) Pentium(R) D CPU 3.00GHz ("GenuineIntel" 686-class) 3.01 GHz
> cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,EST,CNXT-ID,CX16,xTPR
> real mem  = 1071640576 (1021MB)
> avail mem = 1028595712 (980MB)
> mainbus0 at root
> bios0 at mainbus0: AT/286+ BIOS, date 12/31/99, BIOS32 rev. 0 @ 0xf0000, SMBIOS rev. 2.3 @ 0xee000 (47 entries)
> bios0: vendor HP version "W04" date 04/06/2007
> bios0: HP ProLiant DL320 G5
> pcibios0 at bios0: rev 3.0 @ 0xf0000/0x2000
> pcibios0: PCI BIOS has 7 Interrupt Routing table entries
> pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801GB LPC" rev 0x00)
> pcibios0: PCI bus #7 is the last bus
> bios0: ROM list: 0xc0000/0xb000 0xcc400/0x1000 0xcd400/0x1000 0xce400/0x3400! 0xe6000/0x2000!
> acpi at mainbus0 not configured
> ipmi0 at mainbus0: version 2.0 interface KCS iobase 0xca2/2 spacing 1
> cpu0 at mainbus0
> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> pchb0 at pci0 dev 0 function 0 "Intel E7230 MCH" rev 0xc0
> ppb0 at pci0 dev 1 function 0 "Intel E7230 PCIE" rev 0xc0
> pci1 at ppb0 bus 1
> ppb1 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01
> pci2 at ppb1 bus 2
> ppb2 at pci2 dev 0 function 0 "ServerWorks PCIE-PCIX" rev 0xb5
> pci3 at ppb2 bus 3
> bge0 at pci3 dev 4 function 0 "Broadcom BCM5714" rev 0xa3, BCM5715 A3 (0x9003): irq 11, address 00:1b:78:07:c9:9a
> brgphy0 at bge0 phy 1: BCM5714 10/100/1000baseT PHY, rev. 0
> bge1 at pci3 dev 4 function 1 "Broadcom BCM5714" rev 0xa3, BCM5715 A3 (0x9003): irq 10, address 00:1b:78:07:c9:9b
> brgphy1 at bge1 phy 1: BCM5714 10/100/1000baseT PHY, rev. 0
> ppb3 at pci3 dev 8 function 0 "ServerWorks HT-1000 PCIX" rev 0xb4
> pci4 at ppb3 bus 4
> ppb4 at pci0 dev 28 function 4 "Intel 82801G PCIE" rev 0x01
> pci5 at ppb4 bus 5
> em0 at pci5 dev 0 function 0 "Intel PRO/1000 PT (82571EB)" rev 0x06: irq 11, address 00:1b:78:57:58:e0
> em1 at pci5 dev 0 function 1 "Intel PRO/1000 PT (82571EB)" rev 0x06: irq 10, address 00:1b:78:57:58:e1
> ppb5 at pci0 dev 28 function 5 "Intel 82801G PCIE" rev 0x01
> pci6 at ppb5 bus 6
> uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x01: irq 5
> uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x01: irq 5
> uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x01: irq 5
> uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x01: irq 5
> ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x01: irq 5
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0: Intel EHCI root hub, rev 2.00/1.00, addr 1
> ppb6 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0xe1
> pci7 at ppb6 bus 7
> vga1 at pci7 dev 3 function 0 "ATI ES1000" rev 0x02
> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> "Compaq iLO" rev 0x03 at pci7 dev 4 function 0 not configured
> "Compaq iLO" rev 0x03 at pci7 dev 4 function 2 not configured
> uhci4 at pci7 dev 4 function 4 "Hewlett-Packard USB" rev 0x00: irq 11
> uhci4: cannot stop
> "Hewlett-Packard IPMI" rev 0x00 at pci7 dev 4 function 6 not configured
> usb1 at uhci4: USB revision 1.0
> uhub1 at usb1: Hewlett-Packard UHCI root hub, rev 1.00/1.00, addr 1
> ichpcib0 at pci0 dev 31 function 0 "Intel 82801GB LPC" rev 0x01: PM disabled
> pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev 0x01: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility
> pciide0: channel 0 disabled (no drives)
> pciide0: channel 1 disabled (no drives)
> pciide1 at pci0 dev 31 function 2 "Intel 82801GB SATA" rev 0x01: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI
> pciide1: using irq 7 for native-PCI interrupt
> wd0 at pciide1 channel 0 drive 0: <FB160C4081>
> wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
> wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
> usb2 at uhci0: USB revision 1.0
> uhub2 at usb2: Intel UHCI root hub, rev 1.00/1.00, addr 1
> usb3 at uhci1: USB revision 1.0
> uhub3 at usb3: Intel UHCI root hub, rev 1.00/1.00, addr 1
> usb4 at uhci2: USB revision 1.0
> uhub4 at usb4: Intel UHCI root hub, rev 1.00/1.00, addr 1
> usb5 at uhci3: USB revision 1.0
> uhub5 at usb5: Intel UHCI root hub, rev 1.00/1.00, addr 1
> isa0 at ichpcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pmsi0 at pckbc0 (aux slot)
> pckbc0: using irq 12 for aux slot
> wsmouse0 at pmsi0 mux 0
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: <PC speaker>
> spkr0 at pcppi0
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> pccom1: console
> fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
> fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
> biomask ebe5 netmask efe5 ttymask ffe7
> pctr: user-level cycle counter enabled
> mtrr: Pentium Pro MTRR support
> dkcsum: wd0 matches BIOS drive 0x80
> root on wd0a swap on wd0b dump on wd0b
> 
>   I didn't find a way to disable just one uhci device (is there a way?) and
> had to disable all of them:
> 
> OpenBSD 4.2-stable (GENERIC.MP) #8: Thu Oct 18 16:45:14 CDT 2007
>     root@build.twopoint.com:/usr/src/sys/arch/i386/compile/GENERIC.MP
> cpu0: Intel(R) Pentium(R) D CPU 3.00GHz ("GenuineIntel" 686-class) 3.01 GHz
> cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,EST,CNXT-ID,CX16,xTPR
> real mem  = 1071640576 (1021MB)
> avail mem = 1028530176 (980MB)
> mainbus0 at root
> bios0 at mainbus0: AT/286+ BIOS, date 12/31/99, BIOS32 rev. 0 @ 0xf0000, SMBIOS rev. 2.3 @ 0xee000 (47 entries)
> bios0: vendor HP version "W04" date 04/06/2007
> bios0: HP ProLiant DL320 G5
> pcibios0 at bios0: rev 3.0 @ 0xf0000/0x2000
> pcibios0: PCI BIOS has 7 Interrupt Routing table entries
> pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801GB LPC" rev 0x00)
> pcibios0: PCI bus #7 is the last bus
> bios0: ROM list: 0xc0000/0xb000 0xcc400/0x1000 0xcd400/0x1000 0xce400/0x3400! 0xe6000/0x2000!
> acpi0 at mainbus0: rev 2
> acpi0: tables DSDT FACP SPCR MCFG HPET SPMI APIC SSDT
> acpitimer0 at acpi0: 3579545 Hz, 24 bits
> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> cpu0 at mainbus0: apid 0 (boot processor)
> cpu0: apic clock running at 200 MHz
> cpu1 at mainbus0: apid 1 (application processor)
> cpu1: Intel(R) Pentium(R) D CPU 3.00GHz ("GenuineIntel" 686-class) 3.01 GHz
> cpu1: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,EST,CNXT-ID,CX16,xTPR
> ioapic0 at mainbus0: apid 8 pa 0xfec00000, version 20, 24 pins
> acpiprt0 at acpi0: bus 7 (IP2P)
> acpiprt1 at acpi0: bus 4 (PCXS)
> acpiprt2 at acpi0: bus 3 (PCXA)
> acpiprt3 at acpi0: bus 2 (ICHE)
> acpiprt3: no apic found for irq 47
> acpiprt4 at acpi0: bus 5 (IPE4)
> acpiprt5 at acpi0: bus 1 (PTA0)
> acpiprt6 at acpi0: bus 0 (PCI0)
> acpicpu0 at acpi0
> acpicpu1 at acpi0
> acpicpu2 at acpi0
> acpicpu3 at acpi0
> acpicpu4 at acpi0
> acpicpu5 at acpi0
> acpicpu6 at acpi0
> acpicpu7 at acpi0
> acpitz0 at acpi0, critical temperature: 31 degC
> ipmi0 at mainbus0: version 2.0 interface KCS iobase 0xca2/2 spacing 1
> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> pchb0 at pci0 dev 0 function 0 "Intel E7230 MCH" rev 0xc0
> ppb0 at pci0 dev 1 function 0 "Intel E7230 PCIE" rev 0xc0
> pci1 at ppb0 bus 1
> ppb1 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01
> pci2 at ppb1 bus 2
> ppb2 at pci2 dev 0 function 0 "ServerWorks PCIE-PCIX" rev 0xb5
> pci3 at ppb2 bus 3
> bge0 at pci3 dev 4 function 0 "Broadcom BCM5714" rev 0xa3, BCM5715 A3 (0x9003): apic 8 int 16 (irq 11), address 00:1b:78:07:c9:9a
> brgphy0 at bge0 phy 1: BCM5714 10/100/1000baseT PHY, rev. 0
> bge1 at pci3 dev 4 function 1 "Broadcom BCM5714" rev 0xa3, BCM5715 A3 (0x9003): apic 8 int 17 (irq 10), address 00:1b:78:07:c9:9b
> brgphy1 at bge1 phy 1: BCM5714 10/100/1000baseT PHY, rev. 0
> ppb3 at pci3 dev 8 function 0 "ServerWorks HT-1000 PCIX" rev 0xb4
> pci4 at ppb3 bus 4
> ppb4 at pci0 dev 28 function 4 "Intel 82801G PCIE" rev 0x01
> pci5 at ppb4 bus 5
> em0 at pci5 dev 0 function 0 "Intel PRO/1000 PT (82571EB)" rev 0x06: apic 8 int 16 (irq 11), address 00:1b:78:57:58:e0
> em1 at pci5 dev 0 function 1 "Intel PRO/1000 PT (82571EB)" rev 0x06: apic 8 int 17 (irq 10), address 00:1b:78:57:58:e1
> ppb5 at pci0 dev 28 function 5 "Intel 82801G PCIE" rev 0x01
> pci6 at ppb5 bus 6
> "Intel 82801GB USB" rev 0x01 at pci0 dev 29 function 0 not configured
> "Intel 82801GB USB" rev 0x01 at pci0 dev 29 function 1 not configured
> "Intel 82801GB USB" rev 0x01 at pci0 dev 29 function 2 not configured
> "Intel 82801GB USB" rev 0x01 at pci0 dev 29 function 3 not configured
> ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x01: apic 8 int 21 (irq 5)
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0: Intel EHCI root hub, rev 2.00/1.00, addr 1
> ppb6 at pci0 dev 30 function 0 "Intel 82801BA AGP" rev 0xe1
> pci7 at ppb6 bus 7
> vga1 at pci7 dev 3 function 0 "ATI ES1000" rev 0x02
> wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> "Compaq iLO" rev 0x03 at pci7 dev 4 function 0 not configured
> "Compaq iLO" rev 0x03 at pci7 dev 4 function 2 not configured
> "Hewlett-Packard USB" rev 0x00 at pci7 dev 4 function 4 not configured
> "Hewlett-Packard IPMI" rev 0x00 at pci7 dev 4 function 6 not configured
> ichpcib0 at pci0 dev 31 function 0 "Intel 82801GB LPC" rev 0x01: PM disabled
> pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev 0x01: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility
> pciide0: channel 0 disabled (no drives)
> pciide0: channel 1 disabled (no drives)
> pciide1 at pci0 dev 31 function 2 "Intel 82801GB SATA" rev 0x01: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI
> pciide1: using apic 8 int 20 (irq 7) for native-PCI interrupt
> wd0 at pciide1 channel 0 drive 0: <FB160C4081>
> wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
> wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
> isa0 at ichpcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> pmsi0 at pckbc0 (aux slot)
> pckbc0: using irq 12 for aux slot
> wsmouse0 at pmsi0 mux 0
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: <PC speaker>
> spkr0 at pcppi0
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
> pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> pccom1: console
> fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
> fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
> pctr: user-level cycle counter enabled
> mtrr: Pentium Pro MTRR support
> dkcsum: wd0 matches BIOS drive 0x80
> root on wd0a swap on wd0b dump on wd0b
> 
>   The  second issue (maybe related to the first one) - iLO 2 Remote Console
> (requires  an  iLO2  Advanced License) makes the OS (OBSD) to (deadly) hang
> every time you connect. No error messages, no keyboard/IP response, doesn't
> react  to  anything  but  hard  reset signal. This is very sad, because the
> ability to remotely manage/fix servers in case of serious errors was one of
> the reasons to buy a brandname.
> 
> e> Which one's hardware better supported? Internal NIC's, SCSI 
> e> (Sun)/SATA(HP) controllers?
> 
>   Integrated  NICs  are  Broadcom (bge). Their support is not included into
> floppy42.fs,  which  might be a (small) issue. There is also a problem with
> speed  autodetection  if  you  plug the network cable after boot, but doing
> ifconfig down/up resolves it.
> 
>   SATA  is recognized as wd, and working with speed of wd (PATA) - not very
> fast. Shouldn't be an issue for a firewall (may be will slow down squid).
> 
> e> And if you had to choose - what would be your choice today?
> 
>   I would get DELL. ;) But maybe they are just an unknown evil...