We have initial support for AR5210s (still needs work), AR5211 and
AR5212. To add support for other hardware we'll need register dumps of
the HAL. Fortunately we have a way to do this. It's still hard to
figure out what we're supposed to do but at least we can get the some
idea of what to do this way.

Below are instructions, you can find later instructions on the URL:

http://kernel.org/pub/linux/kernel/people/mcgrof/madwifi-regdumps/README

MadWifi HAL Register dumping
----------------------------

You can use these instructions to get register dumps of HAL register
reads and writes. For this we build the alq and mmio trap modules and
make some use of them.

This is based on patches and information from:

http://madwifi.org/ticket/1380
http://nouveau.freedesktop.org/wiki/MmioTrace

-- Steps to take ---

0. Get MadWifi svn trunk, patches, pach up and build:

svn export http://svn.madwifi.org/madwifi/trunk trunk
wget http://kernel.org/pub/linux/kernel/people/mcgrof/madwifi-regdumps/alq.diff
wget http://kernel.org/pub/linux/kernel/people/mcgrof/madwifi-regdumps/mmio.diff
wget http://kernel.org/pub/linux/kernel/people/mcgrof/madwifi-regdumps/var.diff

cd trunk/
patch -p1 < ../alq.patch
patch -p1 < ../mmio.patch
patch -p1 < ../var.diff

make ALQ=1 MMIOTRACE=1

1. Alter the ath_pci.ko module with this command and then install modules:

mv ath/ath_pci.ko ath/ath_pci.ko.old
objcopy --redefine-sym __ioremap=__ioremap_trace --redefine-sym \
	iounmap=iounmap_trace --redefine-sym  \
	ioremap_nocache=ioremap_nocache_trace \
	ath/ath_pci.ko.old ath/ath_pci.ko

sudo make install ALQ=1 MMIOTRACE=1

2. Load mmio, alq, ath_hal

sudo modprobe mmio
sudo modprobe alq
sudo modprobe ath_hal

3. Proc stuff:

sudo su -
echo 2 > /proc/sys/dev/ath/hal/debug
echo 1 > /proc/sys/dev/ath/hal/alq

4. Load ath_pci

modprobe ath_pci

5. Check reg dump file exists

ls -l /tmp/ath_hal.log

As you do things with the driver it should increase in size:

root@pogo:~# wc -l /tmp/ath_hal.log
14236 /tmp/ath_hal.log

root@pogo:~# iwconfig  wlan3
wlan3     IEEE 802.11b  ESSID:""  Nickname:""
          Mode:Managed  Channel:0  Access Point: Not-Associated
          Bit Rate:0 kb/s   Tx-Power:0 dBm   Sensitivity=1/1
          Retry:off   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=0/70  Signal level=-256 dBm  Noise level=-256 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

root@pogo:~# wc -l /tmp/ath_hal.log
14425 /tmp/ath_hal.log

6. Parse the regdump stuff, it looks nasty:

perl -pe 's,\x00,,g' < /tmp/ath_hal.log >  /tmp/ath_hal.log.txt

In the end you should see lines like this:

R:0x04004 = 0x00010000 - unknown
W:0x04004 = 0x00000000 - unknown
R:0x04010 = 0x00010014 - unknown
R:0x04004 = 0x00000000 - unknown
W:0x04004 = 0x00000000 - unknown
...

-- Sending dumps --

Please feel free to post dumps of hardware to ath5k-devel@lists.ath5k.org

In doing so you should also provide ath_info dump:

cd trunk/tools
make
lspci -v
# look for the line like:
# Memory at b8000000 (32-bit, non-prefetchable) [size=64K]
# for your card, put 0x in front of it as and fun ath_info with it:
sudo ./ath_info 0xb8000000

You should get something like:

---

 -==Device Information==-
MAC Version:  5212 (0x50)
MAC Revision: 5213A(0x59)
PHY Revision: 5112a(0x36)
 -==EEPROM Information==-
EEPROM Version:     5.2
EEPROM Size:        16K
Regulatory Domain:  0x10
 -==== Capabilities ====-
|  802.11a Support: yes  |
|  802.11b Support: yes  |
|  802.11g Support: yes  |
|  RFKill  Support: no   |
|  32KHz   Crystal: yes  |
 ========================
GPIO registers: CR 00000000 DO 00000000 DI 00000000

---

Other tips:

If you are sending dumps please add stuff to the regdump which
indicates what you did to trigger a section of reg reads/writes.

The dumps can be pretty big so please compress the file with bzip2. If
you can host the file somewhere and just send us the URL that may
help.

  Luis

-------------------------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc.
Still grepping through log files to find problems?  Stop.
Now Search log events and configuration files using AJAX and a browser.
Download your FREE copy of Splunk now >> http://get.splunk.com/
_______________________________________________
Madwifi-devel mailing list
Madwifi-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/madwifi-devel