Gupta, Ajay Kumar wrote:
quoted text >
> > > >> actualy, should be UHH_SYSCONFIG:SOFTRESET.
> > > >
> > > >That would reset the controller and so all the register would get
> > > >their default values.
> > >
> > > aa, ok. I mis-read, you want to reset the PHY only. Still, the boards
> > > without the reset line, won't work, so a better solution (if any) has to
> > > be found.
> >
> > I agree.
> >
> > >
> > > Maybe driving port reset signal would make PHY act ?
> > >
> > Do you mean to reset PHY using PHY reset command over ULPI ?
> > Anyways would try this.
>
> Soft resetting the PHY also fixes the issue. Here is the version-2 of
> This patch.
>
> -Ajay
> -------- cut here -------------
>
> Currently devices don't get detected automatically if the ehci
> module is inserted 2nd time onward. We need to disconnect and
> reconnect the device for it to get detected and enumerated.
>
> Resetting the USB PHY using PHY reset command over ULPI fixes
> this issue. Tested on OMAP3EVM.
>
Ajay,
I don't currently understand why this is needed. I see that this
fixes a problem for you, but I do not understand why it works.
I would like to test this on the other PHYs that could interface
with the OMAP3 before acking this. I don't have access to them
right now, and I'll try and dig up those boards on Monday and give
it a spin.
- Anand
quoted text > Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
> ---
> drivers/usb/host/ehci-omap.c | 27 +++++++++++++++++++++++++++
> 1 files changed, 27 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
> index 5450e62..dec05fb 100644
> --- a/drivers/usb/host/ehci-omap.c
> +++ b/drivers/usb/host/ehci-omap.c
> @@ -126,6 +126,13 @@
> #define EHCI_INSNREG05_ULPI_EXTREGADD_SHIFT 8
> #define EHCI_INSNREG05_ULPI_WRDATA_SHIFT 0
>
> +/* ULPI Function Control set register */
> +#define FUNCTION_CTRL_SET_OFFSET 0x5
> +#define ULPI_FUNCTION_CTRL_SET_SUSPENDM (1 << 6)
> +#define ULPI_FUNCTION_CTRL_SET_RESET (1 << 5)
> +#define ULPI_FUNCTION_CTRL_SET_OPMODE (3 << 3)
> +#define ULPI_FUNCTION_CTRL_SET_TERMSELECT (1 << 2)
> +#define ULPI_FUNCTION_CTRL_SET_XCVRSELECT (3 << 0)
>
> /*-------------------------------------------------------------------------*/
>
> static inline void ehci_omap_writel(void __iomem *base, u32 reg, u32 val)
> @@ -425,6 +432,26 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
> gpio_set_value(omap->reset_gpio_port[1], 1);
> }
>
> + /* Soft reset the PHY using PHY reset command over ULPI */
> + if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY) {
> + reg = ULPI_FUNCTION_CTRL_SET_RESET
> + | ULPI_FUNCTION_CTRL_SET_SUSPENDM
> + | (0x5 << EHCI_INSNREG05_ULPI_REGADD_SHIFT) /* F_CTRL */
> + | (2 << EHCI_INSNREG05_ULPI_OPSEL_SHIFT) /* WRITE */
> + | (1 << EHCI_INSNREG05_ULPI_PORTSEL_SHIFT) /* PORT1 */
> + | (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT); /* START */
> + ehci_omap_writel(omap->ehci_base, EHCI_INSNREG05_ULPI, reg);
> + }
> + if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY) {
> + reg = ULPI_FUNCTION_CTRL_SET_RESET
> + | ULPI_FUNCTION_CTRL_SET_SUSPENDM
> + | (0x5 << EHCI_INSNREG05_ULPI_REGADD_SHIFT) /* F_CTRL */
> + | (2 << EHCI_INSNREG05_ULPI_OPSEL_SHIFT) /* WRITE */
> + | (2 << EHCI_INSNREG05_ULPI_PORTSEL_SHIFT) /* PORT2 */
> + | (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT); /* START */
> + ehci_omap_writel(omap->ehci_base, EHCI_INSNREG05_ULPI, reg);
> + }
> +
> return 0;
>
> err_sys_status:
> --
> 1.6.2.4
>
> --------- end --------------------
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to
majordomo@vger.kernel.org
More majordomo info at
http://vger.kernel.org/majordomo-info.html
