In general, I've resisted the urge to correct grammar.  Comments below.

Vivek Goyal <vgoyal@redhat.com> writes:

quoted text
> o Some documentation to provide help with tunables.
>
> Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
> ---
>  Documentation/block/cfq-iosched.txt        |   45 ++++++++++++++++++++++++++++
>  Documentation/cgroups/blkio-controller.txt |   28 +++++++++++++++++
>  2 files changed, 73 insertions(+), 0 deletions(-)
>  create mode 100644 Documentation/block/cfq-iosched.txt
>
> diff --git a/Documentation/block/cfq-iosched.txt b/Documentation/block/cfq-iosched.txt
> new file mode 100644
> index 0000000..3ea9e79
> --- /dev/null
> +++ b/Documentation/block/cfq-iosched.txt
> @@ -0,0 +1,45 @@
> +CFQ ioscheduler tunables
> +========================
> +
> +slice_idle
> +----------
> +This specifies how long CFQ should idle for next request on certain cfq queues
> +(for sequential workloads) and service trees (for random workloads) before
> +queue is expired and CFQ selects next queue to dispatch from.
> +
> +By default slice_idle is a non-zero value. That means by default we idle on
> +queues/service trees. This can be very helpful on highly seeky media like

'seeky' is not a  property of the media.  I think you meant on storage
devices with a high seek cost.

quoted text
> +single spindle SATA/SAS disks where we can cut down on overall number of
> +seeks and see improved throughput.
> +
> +Setting slice_idle to 0 will remove all the idling on queues/service tree
> +level and one should see an overall improved throughput on faster storage
> +devices like multiple SATA/SAS disks in hardware RAID configuration. The down
> +side is that isolation provided from WRITES also goes down and notion of
> +IO priority becomes weaker.
> +
> +So depending on storage and workload, it might be useful to set slice_idle=0.
> +In general I think for SATA/SAS disks and software RAID of SATA/SAS disks

You think?  I'm pretty sure we've measured that.  ;-)

quoted text
> +keeping slice_idle enabled should be useful. For any configurations where
> +there are multiple spindles behind single LUN (Host based hardware RAID
> +controller or for storage arrays), setting slice_idle=0 might end up in better
> +throughput and acceptable latencies.
> +
> +CFQ IOPS Mode for group scheduling
> +==================================
> +Basic CFQ design is to provide priority based time slices. Higher priority
> +process gets bigger time slice and lower priority process gets smaller time
> +slice. Measuring time becomes harder if storage is fast and supports NCQ and
> +it would be better to dispatch multiple requests from multiple cfq queues in
> +request queue at a time. In such scenario, it is not possible to measure time
> +consumed by single queue accurately.
> +
> +What is possible though is to measure number of requests dispatched from a
> +single queue and also allow dispatch from multiple cfq queue at the same time.
> +This effectively becomes the fairness in terms of IOPS (IO operations per
> +second).
> +
> +If one sets slice_idle=0 and if storage supports NCQ, CFQ internally switches
> +to IOPS mode and starts providing fairness in terms of number of requests
> +dispatched. Note that this mode switching takes effect only for group
> +scheduling. For non-cgroup users nothing should change.

quoted text
> diff --git a/Documentation/cgroups/blkio-controller.txt b/Documentation/cgroups/blkio-controller.txt
> index 48e0b21..6919d62 100644
> --- a/Documentation/cgroups/blkio-controller.txt
> +++ b/Documentation/cgroups/blkio-controller.txt
> @@ -217,6 +217,7 @@ Details of cgroup files
>  CFQ sysfs tunable
>  =================
>  /sys/block/<disk>/queue/iosched/group_isolation
> +-----------------------------------------------
>  
>  If group_isolation=1, it provides stronger isolation between groups at the
>  expense of throughput. By default group_isolation is 0. In general that
> @@ -243,6 +244,33 @@ By default one should run with group_isolation=0. If that is not sufficient
>  and one wants stronger isolation between groups, then set group_isolation=1
>  but this will come at cost of reduced throughput.
>  
> +/sys/block/<disk>/queue/iosched/slice_idle
> +------------------------------------------
> +On a faster hardware CFQ can be slow, especially with sequential workload.
> +This happens because CFQ idles on a single queue and single queue might not
> +drive deeper request queue depths to keep the storage busy. In such scenarios
> +one can try setting slice_idle=0 and that would switch CFQ to IOPS
> +(IO operations per second) mode on NCQ supporting hardware.
> +
> +That means CFQ will not idle between cfq queues of a cfq group and hence be
> +able to driver higher queue depth and achieve better throughput. That also
> +means that cfq provides fairness among groups in terms of IOPS and not in
> +terms of disk time.

I'm not sure we need documentation of this tunable twice.  Why not just
give guidance on when it should be set to 0 in the next section
(group_idle) and refer to cfq-iosched.txt?

quoted text
> +
> +/sys/block/<disk>/queue/iosched/group_idle
> +------------------------------------------
> +If one disables idling on individual cfq queues and cfq service trees by
> +setting slice_idle=0, group_idle kicks in. That means CFQ will still idle
> +on the group in an attempt to provide fairness among groups.
> +
> +By default group_idle is same as slice_idle and does not do anything if
> +slice_idle is enabled.
> +
> +One can experience an overall throughput drop if you have created multiple
> +groups and put applications in that group which are not driving enough
> +IO to keep disk busy. In that case set group_idle=0, and CFQ will not idle
> +on individual groups and throughput should improve.
> +
>  What works
>  ==========
>  - Currently only sync IO queues are support. All the buffered writes are
                                       supported.

Looks like something is amiss.  Your text was truncated somewhere.

Cheers,
Jeff
--
unsubscribe notice
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/