SH_HICOSH4 doesn't exist in Kconfig, therefore removing all references
for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
---
drivers/net/cs89x0.c | 51 +------------------------------------------------
drivers/net/cs89x0.h | 4 ---
2 files changed, 2 insertions(+), 53 deletions(-)
diff --git a/drivers/net/cs89x0.c b/drivers/net/cs89x0.c
index 7a5d787..d1762fe 100644
--- a/drivers/net/cs89x0.c
+++ b/drivers/net/cs89x0.c
@@ -170,11 +170,7 @@ static char version[] __initdata =
/* The cs8900 has 4 IRQ pins, software selectable. cs8900_irq_map maps
them to system IRQ numbers. This mapping is card specific and is set to
the configuration of the Cirrus Eval board for this chip. */
-#if defined(CONFIG_SH_HICOSH4)
-static unsigned int netcard_portlist[] __used __initdata =
- { 0x0300, 0};
-static unsigned int cs8900_irq_map[] = {1,0,0,0};
-#elif defined(CONFIG_MACH_IXDP2351)
+#if defined(CONFIG_MACH_IXDP2351)
static unsigned int netcard_portlist[] __used __initdata = {IXDP2351_VIRT_CS8900_BASE, 0};
static unsigned int cs8900_irq_map[] = {IRQ_IXDP2351_CS8900, 0, 0, 0};
#elif defined(CONFIG_ARCH_IXDP2X01)
@@ -537,12 +533,6 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
goto out1;
}
-#ifdef CONFIG_SH_HICOSH4
- /* truly reset the chip */
- writeword(ioaddr, ADD_PORT, 0x0114);
- writeword(ioaddr, DATA_PORT, 0x0040);
-#endif
-
/* if they give us an odd I/O address, then do ONE write to
the address port, to get it back to address zero, where we
expect to find the EISA signature word. An IO with a base of 0x3
@@ -608,37 +598,6 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
the driver will always do *something* instead of complain that
adapter_cnf is 0. */
-#ifdef CONFIG_SH_HICOSH4
- if (1) {
- /* For the HiCO.SH4 board, things are different: we don't
- have EEPROM, but there is some data in flash, so we go
- get it there directly (MAC). */
- __u16 *confd;
- short cnt;
- if (((* (volatile __u32 *) 0xa0013ff0) & 0x00ffffff)
- == 0x006c3000) {
- confd = (__u16*) 0xa0013fc0;
- } else {
- confd = (__u16*) 0xa001ffc0;
- }
- cnt = (*confd++ & 0x00ff) >> 1;
- while (--cnt > 0) {
- __u16 j = *confd++;
-
- switch (j & 0x0fff) {
- case PP_IA:
- for (i = 0; i < ETH_ALEN/2; i++) {
- dev->dev_addr[i*2] = confd[i] & 0xFF;
- dev->dev_addr[i*2+1] = confd[i] >> 8;
- }
- break;
- }
- j = (j >> 12) + 1;
- confd += j;
- cnt -= j;
- }
- } else
-#endif
if ((readreg(dev, PP_SelfST) & (EEPROM_OK | EEPROM_PRESENT)) ==
(EEPROM_OK|EEPROM_PRESENT)) {
@@ -693,11 +652,7 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
printk("\n");
/* First check to see if an EEPROM is attached. */
-#ifdef CONFIG_SH_HICOSH4 /* no EEPROM on HiCO, don't hazzle with it here */
- if (1) {
- printk(KERN_NOTICE "cs89x0: No EEPROM on HiCO.SH4\n");
- } else
-#endif
+
if ((readreg(dev, PP_SelfST) & EEPROM_PRESENT) == 0)
printk(KERN_WARNING "cs89x0: No EEPROM, relying on command line....\n");
else if (get_eeprom_data(dev, START_EEPROM_DATA,CHKSUM_LEN,eeprom_buff) < 0) {
@@ -1234,7 +1189,6 @@ net_open(struct net_device *dev)
int i;
int ret;
-#if !defined(CONFIG_SH_HICOSH4) && !defined(CONFIG_ARCH_PNX010X) /* uses irq#1, so this won't work */
if (dev->irq < 2) {
/* Allow interrupts to be generated by the chip */
/* Cirrus' release had this: */
@@ -1263,7 +1217,6 @@ net_open(struct net_device *dev)
}
}
else
-#endif
{
#ifndef CONFIG_CS89x0_NONISA_IRQ
if (((1 << dev->irq) & lp->irq_map) == 0) {
diff --git a/drivers/net/cs89x0.h b/drivers/net/cs89x0.h
index 204ed37..91423b7 100644
--- a/drivers/net/cs89x0.h
+++ b/drivers/net/cs89x0.h
@@ -437,11 +437,7 @@
#define IRQ_MAP_EEPROM_DATA 0x0046 /* Offset into eeprom for the IRQ map */
#define IRQ_MAP_LEN 0x0004 /* No of bytes to read for the IRQ map */
#define PNP_IRQ_FRMT 0x0022 /* PNP small item IRQ format */
-#ifdef CONFIG_SH_HICOSH4
-#define CS8900_IRQ_MAP 0x0002 /* HiCO-SH4 board has its IRQ on #1 */
-#else
#define CS8900_IRQ_MAP 0x1c20 /* This IRQ map is fixed */
-#endif
#define CS8920_NO_INTS 0x0F /* Max CS8920 interrupt select # */
--
1.7.0.4
--
