ARCH_PNX010X doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
---
drivers/net/cs89x0.c | 45 ---------------------------------------------
1 files changed, 0 insertions(+), 45 deletions(-)
diff --git a/drivers/net/cs89x0.c b/drivers/net/cs89x0.c
index 2ccb9f1..7a5d787 100644
--- a/drivers/net/cs89x0.c
+++ b/drivers/net/cs89x0.c
@@ -180,12 +180,6 @@ static unsigned int cs8900_irq_map[] = {IRQ_IXDP2351_CS8900, 0, 0, 0};
#elif defined(CONFIG_ARCH_IXDP2X01)
static unsigned int netcard_portlist[] __used __initdata = {IXDP2X01_CS8900_VIRT_BASE, 0};
static unsigned int cs8900_irq_map[] = {IRQ_IXDP2X01_CS8900, 0, 0, 0};
-#elif defined(CONFIG_ARCH_PNX010X)
-#include <mach/gpio.h>
-#define CIRRUS_DEFAULT_BASE IO_ADDRESS(EXT_STATIC2_s0_BASE + 0x200000) /* = Physical address 0x48200000 */
-#define CIRRUS_DEFAULT_IRQ VH_INTC_INT_NUM_CASCADED_INTERRUPT_1 /* Event inputs bank 1 - ID 35/bit 3 */
-static unsigned int netcard_portlist[] __used __initdata = {CIRRUS_DEFAULT_BASE, 0};
-static unsigned int cs8900_irq_map[] = {CIRRUS_DEFAULT_IRQ, 0, 0, 0};
#elif defined(CONFIG_MACH_MX31ADS)
#include <mach/board-mx31ads.h>
static unsigned int netcard_portlist[] __used __initdata = {
@@ -372,18 +366,6 @@ writeword(unsigned long base_addr, int portno, u16 value)
{
__raw_writel(value, base_addr + (portno << 1));
}
-#elif defined(CONFIG_ARCH_PNX010X)
-static u16
-readword(unsigned long base_addr, int portno)
-{
- return inw(base_addr + (portno << 1));
-}
-
-static void
-writeword(unsigned long base_addr, int portno, u16 value)
-{
- outw(value, base_addr + (portno << 1));
-}
#else
static u16
readword(unsigned long base_addr, int portno)
@@ -546,30 +528,6 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
#endif
}
-#ifdef CONFIG_ARCH_PNX010X
- initialize_ebi();
-
- /* Map GPIO registers for the pins connected to the CS8900a. */
- if (map_cirrus_gpio() < 0)
- return -ENODEV;
-
- reset_cirrus();
-
- /* Map event-router registers. */
- if (map_event_router() < 0)
- return -ENODEV;
-
- enable_cirrus_irq();
-
- unmap_cirrus_gpio();
- unmap_event_router();
-
- dev->base_addr = ioaddr;
-
- for (i = 0 ; i < 3 ; i++)
- readreg(dev, 0);
-#endif
-
/* Grab the region so we can find another board if autoIRQ fails. */
/* WTF is going on here? */
if (!request_region(ioaddr & ~3, NETCARD_IO_EXTENT, DRV_NAME)) {
@@ -1391,9 +1349,6 @@ net_open(struct net_device *dev)
case A_CNF_MEDIA_10B_2: result = lp->adapter_cnf & A_CNF_10B_2; break;
default: result = lp->adapter_cnf & (A_CNF_10B_T | A_CNF_AUI | A_CNF_10B_2);
}
-#ifdef CONFIG_ARCH_PNX010X
- result = A_CNF_10B_T;
-#endif
if (!result) {
printk(KERN_ERR "%s: EEPROM is configured for unavailable media\n", dev->name);
release_dma:
--
1.7.0.4
--
