Home » Mailing list archives » linux-kernel » 2010 » March » 24

My old laptop that is from Acer Aspire 1350 series doesn't halt with 2.6.34-rc[12]

Previous thread: [PATCH] IRQ: move two IRQ functions from .init.text to .text by Henrik Kretzschmar on Wednesday, March 24, 2010 - 4:59 am. (3 messages)

Next thread: [PATCH] Fix section mismatches in virtual framebuffer by Henrik Kretzschmar on Wednesday, March 24, 2010 - 5:17 am. (4 messages)
[view original message]
From: Pauli Nieminen
Subject: My old laptop that is from Acer Aspire 1350 series doesn't halt with 2.6.34-rc[12]
Date: Wednesday, March 24, 2010 - 5:05 am

Hi!

I just recently upgraded from 2.6.33-rc8 to 2.6.33-rc1 (just before
rc2 release).

When I try to shutdown the laptop it fails to halt. Result is that my
computer reboots. If I then select from grub old kernel I can still
correctly shutdown my computer.

Can I try to recompile only some specific module to try to find the
bad commit? I would prefer not to recompile whole kernel if try to
bisect.

lspci --vvvnn:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT8378 [KM400/A]
Chipset Host Bridge [1106:3205]
	Subsystem: VIA Technologies, Inc. Device [1106:7205]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 8
	Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
	Capabilities: [80] AGP version 3.5
		Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit-
FW- AGP3+ Rate=x4,x8
		Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: agpgart-via
	Kernel modules: via-agp

00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8235 PCI Bridge [1106:b168]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00009000-00009fff
	Memory behind bridge: d0100000-d01fffff
	Prefetchable memory behind bridge: d8000000-dfffffff
	Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- ...
[ message continues ]
Previous thread: [PATCH] IRQ: move two IRQ functions from .init.text to .text by Henrik Kretzschmar on Wednesday, March 24, 2010 - 4:59 am. (3 messages)

Next thread: [PATCH] Fix section mismatches in virtual framebuffer by Henrik Kretzschmar on Wednesday, March 24, 2010 - 5:17 am. (4 messages)