Having CY82C693_DEBUG_INFO is enough nowadays.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
---
drivers/ide/pci/cy82c693.c | 51 ---------------------------------------------
1 file changed, 51 deletions(-)
Index: b/drivers/ide/pci/cy82c693.c
===================================================================
--- a/drivers/ide/pci/cy82c693.c
+++ b/drivers/ide/pci/cy82c693.c
@@ -53,7 +53,6 @@
/*
* The following are used to debug the driver.
*/
-#define CY82C693_DEBUG_LOGS 0
#define CY82C693_DEBUG_INFO 0
/*
@@ -172,17 +171,6 @@ static void cy82c693_set_dma_mode(ide_dr
index = hwif->channel ? CY82_INDEX_CHANNEL1 : CY82_INDEX_CHANNEL0;
-#if CY82C693_DEBUG_LOGS
- /* for debug let's show the previous values */
-
- outb(index, CY82_INDEX_PORT);
- data = inb(CY82_DATA_PORT);
-
- printk(KERN_INFO "%s (ch=%d, dev=%d): DMA mode is %d (single=%d)\n",
- drive->name, HWIF(drive)->channel, drive->select.b.unit,
- (data&0x3), ((data>>2)&1));
-#endif /* CY82C693_DEBUG_LOGS */
-
data = (mode & 3) | (single << 2);
outb(index, CY82_INDEX_PORT);
@@ -232,45 +220,6 @@ static void cy82c693_set_pio_mode(ide_dr
}
}
-#if CY82C693_DEBUG_LOGS
- /* for debug let's show the register values */
-
- if (drive->select.b.unit == 0) {
- /*
- * get master drive registers
- * address setup control register
- * is 32 bit !!!
- */
- pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
- addrCtrl &= 0x0F;
-
- /* now let's get the remaining registers */
- pci_read_config_byte(dev, CY82_IDE_MASTER_IOR, &pclk.time_16r);
- pci_read_config_byte(dev, CY82_IDE_MASTER_IOW, &pclk.time_16w);
- pci_read_config_byte(dev, CY82_IDE_MASTER_8BIT, &pclk.time_8);
- } else {
- /*
- * set slave drive registers
- * address setup control register
- * is 32 bit !!!
- */
- pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
-
- addrCtrl &= 0xF0;
- addrCtrl >>= 4;
-
- /* now let's get the remaining registers */
- pci_read_config_byte(dev, CY82_IDE_SLAVE_IOR, &pclk.time_16r);
- pci_read_config_byte(dev, CY82_IDE_SLAVE_IOW, &pclk.time_16w);
- pci_read_config_byte(dev, CY82_IDE_SLAVE_8BIT, &pclk.time_8);
- }
-
- printk(KERN_INFO "%s (ch=%d, dev=%d): PIO timing is "
- "(addr=0x%X, ior=0x%X, iow=0x%X, 8bit=0x%X)\n",
- drive->name, hwif->channel, drive->select.b.unit,
- addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8);
-#endif /* CY82C693_DEBUG_LOGS */
-
/* let's calc the values for this PIO mode */
compute_clocks(pio, &pclk);
--
