At Sun, 29 Jun 2008 19:46:49 +0200,
Rafael J. Wysocki wrote:
quoted text
> 
> On Tuesday, 10 of June 2008, Takashi Iwai wrote:
> > At Mon, 9 Jun 2008 22:45:01 +0200,
> > Rafael J. Wysocki wrote:
> > > 
> > > On Monday, 9 of June 2008, Rafael J. Wysocki wrote:
> > > > On Monday, 9 of June 2008, Takashi Iwai wrote:
> > > > > At Sun, 8 Jun 2008 23:03:58 +0200,
> > > > > Rafael J. Wysocki wrote:
> > > > > > 
> > > > > > Hi,
> > > > > > 
> > > > > > snd-emu10k1 doesn't work on one of my test boxes.  The driver apparently loads,
> > > > > > but the card is not visible, for example, to any mixer apps (including the ALSA
> > > > > > mixer).  However, YaST correctly detects and reports the card (the system is
> > > > > > openSUSE 10.3, x86-64).  The openSUSE-made kernel (2.6.22-something) does
> > > > > > correctly work on the same hardware.
> > > > > > 
> > > > > > Is there anything I should pay attention to, like any options related to /proc
> > > > > > or sysfs that could have an effect on the audio adapter?
> > > > > 
> > > > > First off, check /proc/asound/cards whether snd-emu10k1 driver is
> > > > > really loaded on the first slot.  I guess something else occupies the
> > > > > position.
> > > > 
> > > > This is quite possible, as there is an on-board audio in this box too and I'm
> > > > not sure if the setup switch really turns it off.
> > > > 
> > > > > If yes, a simple solution is to add the following option for snd module:
> > > > > 
> > > > > 	options snd slots=snd-emu10k1
> > > > > 
> > > > > then the first slot is reserved for emu10k1.  Note that this option is
> > > > > available for 2.6.25 or later kernel.
> > > > 
> > > > I'll try later today and let you know.
> > > 
> > > No, it didn't work.
> > > 
> > > Here's what I got from /proc/asound/cards:
> > > 
> > >  0 [Audigy         ]: Audigy - Audigy 1 [SB0090]
> > >                       Audigy 1 [SB0090] (rev.3, serial:0x531102) at 0xa000, irq 17
> > >  1 [UART           ]: MPU-401 UART - MPU-401 UART
> > >                       MPU-401 UART at 0x330, irq 10
> > > 
> > > so I think this is correct, and the "options snd slots=snd-emu10k1" thing had
> > > no visible effect.
> > 
> > Then this must be OK.  Then the remaining possible problems are:
> > 
> > - Device files and permissions.
> >   Check whether /dev/snd/* files exist and have proper permissions and
> >   ACL (see "getfacl /dev/snd/*")
> > 
> > - The default ALSA configuration is hijacked, e.g. via pulse plugin.
> >   Try to remove /etc/asound-pulse.conf if present.
> 
> I've just installed openSUSE 11.0 on this box and the distro kernel
> 2.6.25.5-something works, but 2.6.26-rc8 doesn't.  The symptoms are exactly
> the same as described in this thread and the kernel is the only system
> component replaced.
> 
> So this is a regression from 2.6.25, actually.  Do you want me to bisect?

Hmm... there is really no visible problematic changes for emu10k1
between 2.6.25 and 2.6.26.  I guess checking /proc/asound/cards and/or
kernel config would save the time of bisect.  At least, check the
following:

1. you have emu10k1 in the first entry (#0) of /proc/asound/cards
2. the mixer states are OK (e.g. "Audigy Analog/Digital Output
Jack" switch is off, "Master" and "PCM" are muted/adjusted, etc)
3. run "aplay -Dhw:0 /usr/share/sounds/alsa/test.wav" for testing


thanks,

Takashi
--
unsubscribe notice
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/