On Tuesday, 10 of June 2008, Takashi Iwai wrote:
quoted text
> At Mon, 9 Jun 2008 22:45:01 +0200,
> Rafael J. Wysocki wrote:
> > 
> > On Monday, 9 of June 2008, Rafael J. Wysocki wrote:
> > > On Monday, 9 of June 2008, Takashi Iwai wrote:
> > > > At Sun, 8 Jun 2008 23:03:58 +0200,
> > > > Rafael J. Wysocki wrote:
> > > > > 
> > > > > Hi,
> > > > > 
> > > > > snd-emu10k1 doesn't work on one of my test boxes.  The driver apparently loads,
> > > > > but the card is not visible, for example, to any mixer apps (including the ALSA
> > > > > mixer).  However, YaST correctly detects and reports the card (the system is
> > > > > openSUSE 10.3, x86-64).  The openSUSE-made kernel (2.6.22-something) does
> > > > > correctly work on the same hardware.
> > > > > 
> > > > > Is there anything I should pay attention to, like any options related to /proc
> > > > > or sysfs that could have an effect on the audio adapter?
> > > > 
> > > > First off, check /proc/asound/cards whether snd-emu10k1 driver is
> > > > really loaded on the first slot.  I guess something else occupies the
> > > > position.
> > > 
> > > This is quite possible, as there is an on-board audio in this box too and I'm
> > > not sure if the setup switch really turns it off.
> > > 
> > > > If yes, a simple solution is to add the following option for snd module:
> > > > 
> > > > 	options snd slots=snd-emu10k1
> > > > 
> > > > then the first slot is reserved for emu10k1.  Note that this option is
> > > > available for 2.6.25 or later kernel.
> > > 
> > > I'll try later today and let you know.
> > 
> > No, it didn't work.
> > 
> > Here's what I got from /proc/asound/cards:
> > 
> >  0 [Audigy         ]: Audigy - Audigy 1 [SB0090]
> >                       Audigy 1 [SB0090] (rev.3, serial:0x531102) at 0xa000, irq 17
> >  1 [UART           ]: MPU-401 UART - MPU-401 UART
> >                       MPU-401 UART at 0x330, irq 10
> > 
> > so I think this is correct, and the "options snd slots=snd-emu10k1" thing had
> > no visible effect.
> 
> Then this must be OK.  Then the remaining possible problems are:
> 
> - Device files and permissions.
>   Check whether /dev/snd/* files exist and have proper permissions and
>   ACL (see "getfacl /dev/snd/*")
> 
> - The default ALSA configuration is hijacked, e.g. via pulse plugin.
>   Try to remove /etc/asound-pulse.conf if present.

I've just installed openSUSE 11.0 on this box and the distro kernel
2.6.25.5-something works, but 2.6.26-rc8 doesn't.  The symptoms are exactly
the same as described in this thread and the kernel is the only system
component replaced.

So this is a regression from 2.6.25, actually.  Do you want me to bisect?

Rafael
--
unsubscribe notice
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/