Re: [2.6.25.1] qla2xxx can't see more than 4 drives

Score:

Previous message: [thread] [date] [author]
Next message: [thread] [date] [author]

[view in full thread]

From: Gerhard Mack <gmack@...>

To: Andrew Vasquez <andrew.vasquez@...>

Cc: <linux-scsi@...>, <linux-kernel@...>

Subject: Re: [2.6.25.1] qla2xxx can't see more than 4 drives

Date: Tuesday, May 6, 2008 - 10:28 am

On Tue, 6 May 2008, Andrew Vasquez wrote:

quoted text> Date: Tue, 6 May 2008 06:51:18 -0700
> From: Andrew Vasquez <andrew.vasquez@qlogic.com>
> To: Gerhard Mack <gmack@innerfire.net>
> Cc: linux-scsi@vger.kernel.org, linux-kernel@vger.kernel.org
> Subject: Re: [2.6.25.1] qla2xxx can't see more than 4 drives
> 
> On Sat, 03 May 2008, Gerhard Mack wrote:
> 
> > I have an array witjh 6 drives in it and if use the card's utilities on 
> > boot it sees all of them but for some reason Linux only sees 4 drives.
> > 
> > Am I running into a limit?  I can see both drives if I remove other drives 
> > from the array.
> > 
> > [0:0:0:0]    disk    MAXTOR   ATLAS10K4_36SCA  DFM0  /dev/sda
> > [0:0:1:0]    disk    MAXTOR   ATLAS10K4_36SCA  DFM0  /dev/sdb
> > [0:0:2:0]    disk    MAXTOR   ATLAS10K4_36SCA  DFM0  /dev/sdc
> > [0:0:6:0]    process PE/PV    1x3 SCSI BP      0.28  -
> > fiber channel drives:
> > [2:0:0:0]    disk    SEAGATE  ST314680 CLAR146 7A0A  /dev/sdd
> > [2:0:1:0]    disk    SEAGATE  ST314680 CLAR146 7A04  /dev/sde
> > [2:0:2:0]    disk    SEAGATE  ST314680 CLAR146 7A0A  /dev/sdf
> > [2:0:3:0]    disk    SEAGATE  ST314680 CLAR146 7A04  /dev/sdg
> > 
> > QLogic Fibre Channel HBA Driver
> > qla2xxx 0000:02:0a.0: Found an ISP2312, irq 24, iobase 0xf88cc000
> > qla2xxx 0000:02:0a.0: Configuring PCI space...
> > qla2xxx 0000:02:0a.0: Configure NVRAM parameters...
> > qla2xxx 0000:02:0a.0: Verifying loaded RISC code...
> > qla2xxx 0000:02:0a.0: Allocated (412 KB) for firmware dump...
> > scsi3 : qla2xxx
> > qla2xxx 0000:02:0a.0: LIP reset occured (f8f7).
> > qla2xxx 0000:02:0a.0: LIP occured (f8f7).
> > qla2xxx 0000:02:0a.0: LOOP UP detected (1 Gbps).
> 
> Could you load the driver with the ql2xextended_error_logging module
> parameter set to 1 and send the resultant driver logs?  Also, it would
> could you also send the output of the following after the driver is
> loaded:
> 
> $ cat /sys/class/fc_host/host<host_no>
> $ cat /sys/class/scsi_host/host<host_no>/*
> $ cat /sys/class/fc_remote_ports/*
> 
> where host_no corresponds to the SCSI host-number assigned to the HBA.
> 
Of course.. 

QLogic Fibre Channel HBA Driver
qla2xxx 0000:02:0a.0: Found an ISP2312, irq 24, iobase 0xf88cc000
qla2xxx 0000:02:0a.0: Configuring PCI space...
qla2xxx 0000:02:0a.0: Configure NVRAM parameters...
qla2xxx 0000:02:0a.0: Verifying loaded RISC code...
scsi(4): **** Load RISC code ****
scsi(4): Verifying Checksum of loaded RISC code.
scsi(4): Checksum OK, start firmware.
qla2xxx 0000:02:0a.0: Allocated (412 KB) for firmware dump...
scsi(4): Issue init firmware.
DEBUG: detect hba 4 at address = f5da2278
scsi4 : qla2xxx
scsi(4): Asynchronous LIP RESET (f8f7).
qla2xxx 0000:02:0a.0: LIP reset occured (f8f7).
scsi(4): LIP occured (f8f7).
qla2xxx 0000:02:0a.0: LIP occured (f8f7).
scsi(4): Asynchronous LOOP UP (1 Gbps).
qla2xxx 0000:02:0a.0: LOOP UP detected (1 Gbps).
scsi(4): Asynchronous PORT UPDATE.
scsi(4): Port database changed ffff 0006 0000.
scsi(4): qla2x00_reset_marker()
scsi(4): qla2x00_loop_resync()
scsi(4): F/W Ready - OK 
scsi(4): fw_state=3 curr time=1371fd39.
scsi(4): Configure loop -- dpc flags =0x40800e0
qla2x00_mailbox_command(4): **** FAILED. mbx0=4006, mbx1=7e, mbx2=0, cmd=6a ****
qla2x00_get_port_name(4): failed=102.
scsi(4): MBC_GET_PORT_NAME Failed, No FL Port
scsi(4): LOOP READY
scsi(4): qla2x00_loop_resync - end
qla2xxx 0000:02:0a.0: scsi(4:0:0:0): Queue depth adjusted-up to 4.
scsi 4:0:0:0: Direct-Access     SEAGATE  ST314680 CLAR146 7A0A PQ: 0 ANSI: 3
sd 4:0:0:0: [sdd] 286749476 512-byte hardware sectors (146816 MB)
sd 4:0:0:0: [sdd] Write Protect is off
sd 4:0:0:0: [sdd] Mode Sense: a7 00 10 08
sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 4:0:0:0: [sdd] 286749476 512-byte hardware sectors (146816 MB)
sd 4:0:0:0: [sdd] Write Protect is off
sd 4:0:0:0: [sdd] Mode Sense: a7 00 10 08
sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
 sdd:<6>qla2xxx 0000:02:0a.0: 
 QLogic Fibre Channel HBA Driver: 8.02.00-k9-debug
  QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel
  ISP2312: PCI (66 MHz) @ 0000:02:0a.0 hdma-, host#=4, fw=3.03.20 IPX
 unknown partition table
sd 4:0:0:0: [sdd] Attached SCSI disk
sd 4:0:0:0: Attached scsi generic sg4 type 0
sd 4:0:0:0: Embedded Enclosure Device
sd 4:0:0:0: Failed to get diagnostic page 0x6000000
sd 4:0:0:0: Failed to bind enclosure -19
qla2xxx 0000:02:0a.0: scsi(4:0:1:0): Queue depth adjusted-up to 4.
scsi 4:0:1:0: Direct-Access     SEAGATE  ST314680 CLAR146 7A04 PQ: 0 ANSI: 3
sd 4:0:1:0: [sde] 286749476 512-byte hardware sectors (146816 MB)
sd 4:0:1:0: [sde] Write Protect is off
sd 4:0:1:0: [sde] Mode Sense: a7 00 10 08
sd 4:0:1:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 4:0:1:0: [sde] 286749476 512-byte hardware sectors (146816 MB)
sd 4:0:1:0: [sde] Write Protect is off
sd 4:0:1:0: [sde] Mode Sense: a7 00 10 08
sd 4:0:1:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
 sde: unknown partition table
sd 4:0:1:0: [sde] Attached SCSI disk
sd 4:0:1:0: Attached scsi generic sg5 type 0
sd 4:0:1:0: Embedded Enclosure Device
sd 4:0:1:0: Failed to get diagnostic page 0x6000000
sd 4:0:1:0: Failed to bind enclosure -19
qla2xxx 0000:02:0a.0: scsi(4:0:2:0): Queue depth adjusted-up to 4.
scsi 4:0:2:0: Direct-Access     SEAGATE  ST314680 CLAR146 7A0A PQ: 0 ANSI: 3
sd 4:0:2:0: [sdf] 286749476 512-byte hardware sectors (146816 MB)
sd 4:0:2:0: [sdf] Write Protect is off
sd 4:0:2:0: [sdf] Mode Sense: a7 00 10 08
sd 4:0:2:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 4:0:2:0: [sdf] 286749476 512-byte hardware sectors (146816 MB)
sd 4:0:2:0: [sdf] Write Protect is off
sd 4:0:2:0: [sdf] Mode Sense: a7 00 10 08
sd 4:0:2:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
 sdf: unknown partition table
sd 4:0:2:0: [sdf] Attached SCSI disk
sd 4:0:2:0: Attached scsi generic sg6 type 0
sd 4:0:2:0: Embedded Enclosure Device
qla2xxx_eh_abort(4): aborting sp f7fce920 from RISC. pid=95.
scsi(4): ABORT status detected 0x5-0x0.
qla2xxx 0000:02:0a.0: scsi(4:2:0): Abort command issued -- 1 5f 2002.
qla2xxx_eh_abort(4): aborting sp f7fce920 from RISC. pid=110.
scsi(4): ABORT status detected 0x5-0x0.
qla2xxx 0000:02:0a.0: scsi(4:2:0): Abort command issued -- 1 6e 2002.
qla2xxx_eh_abort(4): aborting sp f7fce920 from RISC. pid=112.
scsi(4): ABORT status detected 0x5-0x0.
qla2xxx 0000:02:0a.0: scsi(4:2:0): Abort command issued -- 1 70 2002.
qla2xxx_eh_abort(4): aborting sp f7fce920 from RISC. pid=115.
scsi(4): ABORT status detected 0x5-0x0.
qla2xxx 0000:02:0a.0: scsi(4:2:0): Abort command issued -- 1 73 2002.
sd 4:0:2:0: Failed to get diagnostic page 0x80000
sd 4:0:2:0: Failed to bind enclosure -19
qla2xxx 0000:02:0a.0: scsi(4:0:3:0): Queue depth adjusted-up to 4.
scsi 4:0:3:0: Direct-Access     SEAGATE  ST314680 CLAR146 7A04 PQ: 0 ANSI: 3
sd 4:0:3:0: [sdg] 286749476 512-byte hardware sectors (146816 MB)
sd 4:0:3:0: [sdg] Write Protect is off
sd 4:0:3:0: [sdg] Mode Sense: a7 00 10 08
sd 4:0:3:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 4:0:3:0: [sdg] 286749476 512-byte hardware sectors (146816 MB)
sd 4:0:3:0: [sdg] Write Protect is off
sd 4:0:3:0: [sdg] Mode Sense: a7 00 10 08
sd 4:0:3:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
 sdg: unknown partition table
sd 4:0:3:0: [sdg] Attached SCSI disk
sd 4:0:3:0: Attached scsi generic sg7 type 0
sd 4:0:3:0: Embedded Enclosure Device
qla2xxx_eh_abort(4): aborting sp f6ddb160 from RISC. pid=137.
scsi(4): ABORT status detected 0x5-0x0.
qla2xxx 0000:02:0a.0: scsi(4:3:0): Abort command issued -- 1 89 2002.
qla2xxx_eh_abort(4): aborting sp f73c4a80 from RISC. pid=149.
scsi(4): ABORT status detected 0x5-0x0.
qla2xxx 0000:02:0a.0: scsi(4:3:0): Abort command issued -- 1 95 2002.
qla2xxx_eh_abort(4): aborting sp f6ddb080 from RISC. pid=158.
scsi(4): ABORT status detected 0x5-0x0.
qla2xxx 0000:02:0a.0: scsi(4:3:0): Abort command issued -- 1 9e 2002.
qla2xxx_eh_abort(4): aborting sp f6ddb080 from RISC. pid=161.
scsi(4): ABORT status detected 0x5-0x0.
qla2xxx 0000:02:0a.0: scsi(4:3:0): Abort command issued -- 1 a1 2002.
sd 4:0:3:0: Failed to get diagnostic page 0x80000
sd 4:0:3:0: Failed to bind enclosure -19

cat /sys/class/fc_host/host4/* :
0x200000e08b127d20
0
0x200000e08b127d20
0
0x000001
0x210000e08b127d20
Online
LPort (private loop)
1 Gbit
Class 3
QLA2340 FW:v3.03.20 DVR:v8.02.00-k9-debug

wwpn (World Wide Port Name)

cat /sys/class/scsi_host/host4/* :
Initiator
Disabled
2176
3
8.02.00-k9-debug
3.03.20 IPX
0
4953 5020 2020 0002
ISP2312
133MHz PCI-X to 2Gb FC, Single Channel
QLA2340
1.54
0.00
0.00
0.00.00 0
PCI (66 MHz)
<NULL>
L87965
128
Link Up - Loop
Initiator
0
0
Disabled
200 us

cat /sys/class/fc_remote_ports/rport-4\:0-0/*  :
35
0x2000000c507ce546
0x0000e2
0x2200000c507ce546
Online
FCP Target
0
Class 3

cat /sys/class/fc_remote_ports/rport-4\:0-1/*
35
0x20000004cf69c688
0x0000e1
0x22000004cf69c688
Online
FCP Target
1
Class 3

cat /sys/class/fc_remote_ports/rport-4\:0-2/* | log
35
0x2000000c507ce809
0x00000f
0x2200000c507ce809
Online
FCP Target
2
Class 3

cat /sys/class/fc_remote_ports/rport-4\:0-3/* :
35
0x20000004cf69b98f
0x000008
0x22000004cf69b98f
Online
FCP Target
3
Class 3

--
Gerhard Mack

gmack@innerfire.net

<>< As a computer I find your faith in technology amusing.
--
unsubscribe noticeTo unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Previous message: [thread] [date] [author]
Next message: [thread] [date] [author]

Messages in current thread:

[2.6.25.1] qla2xxx can't see more than 4 drives, Gerhard Mack, (Sat May 3, 3:17 pm)

Re: [2.6.25.1] qla2xxx can't see more than 4 drives, Andrew Vasquez, (Tue May 6, 9:51 am)

Re: [2.6.25.1] qla2xxx can't see more than 4 drives, Gerhard Mack, (Tue May 6, 10:28 am)

Re: [2.6.25.1] qla2xxx can't see more than 4 drives, Andrew Vasquez, (Tue May 6, 6:08 pm)

Re: [2.6.25.1] qla2xxx can't see more than 4 drives, Gerhard Mack, (Wed May 7, 12:05 pm)

Re: [2.6.25.1] qla2xxx can't see more than 4 drives, Andrew Vasquez, (Wed May 7, 12:59 pm)


linux-kernel:
Greg Kroah-Hartman	[PATCH 009/196] Chinese: add translation of sparse.txt
James Bottomley	[Ksummit-2008-discuss] Fixing the Kernel Janitors project
Joerg Roedel	[PATCH 7/8] x86: move dma_*_coherent functions to include file
Luciano Rocha	usb hdd problems with 2.6.27.2
git:
Marco Costalba	Re: git-commit fatal: Out of memory? mmap failed: Bad file descriptor
Wink Saville	Resolving conflicts
Gregory Jefferis	Re: CRLF problems with Git on Win32
ir0s	Local branch ahead of tracked remote branch but git push claims everything up-to-d...
openbsd-misc:
Siju George	This is what Linus Torvalds calls openBSD crowd
Richard Stallman	Real men don't attack straw men
Todd Pytel	IDE or SCSI virtual disks for VMWare image?
Clint Pachl	Network Time Synchronization using timed or ntpd or a Combination?
linux-netdev:
Linus Torvalds	Re: [GIT]: Networking
Jarek Poplawski	[PATCH] pkt_sched: Destroy gen estimators under rtnl_lock().
Tomasz Grobelny	Re: [DCCP] [RFC] [Patchv2 1/1]: Queuing policies -- reworked version of Tomasz's p...
Jeff Garzik	Re: [bug?] tg3: Failed to load firmware "tigon/tg3_tso.bin"


Serial Driver Implementation Help	15 hours ago	Linux kernel
aacraid bad	16 hours ago	Linux general
Tools: GCC 3.4.6, Final GCC 3 Release	1 day ago	Applications and Utilities
GNU/Hurd is so awful	2 days ago	GNU/Hurd
read /dev/mem not working in 2.6	4 days ago	Linux general
Issues with NETLINK sockets	5 days ago	Linux kernel
Anyone experiancing compiling issues with 2.6.26.6 patching with rt patch 2.6.26.6-rt11?	5 days ago	Linux kernel
Change network interface from eth0 to ppp0	5 days ago	Linux general
kernel module to intercept socket creation	5 days ago	Linux kernel
command to set Subnet Mask	6 days ago	Linux general

Re: [2.6.25.1] qla2xxx can't see more than 4 drives

Online users