I have an array witjh 6 drives in it and if use the card's utilities on
boot it sees all of them but for some reason Linux only sees 4 drives.
Am I running into a limit? I can see both drives if I remove other drives
from the array.
[0:0:0:0] disk MAXTOR ATLAS10K4_36SCA DFM0 /dev/sda
[0:0:1:0] disk MAXTOR ATLAS10K4_36SCA DFM0 /dev/sdb
[0:0:2:0] disk MAXTOR ATLAS10K4_36SCA DFM0 /dev/sdc
[0:0:6:0] process PE/PV 1x3 SCSI BP 0.28 -
fiber channel drives:
[2:0:0:0] disk SEAGATE ST314680 CLAR146 7A0A /dev/sdd
[2:0:1:0] disk SEAGATE ST314680 CLAR146 7A04 /dev/sde
[2:0:2:0] disk SEAGATE ST314680 CLAR146 7A0A /dev/sdf
[2:0:3:0] disk SEAGATE ST314680 CLAR146 7A04 /dev/sdg
QLogic Fibre Channel HBA Driver
qla2xxx 0000:02:0a.0: Found an ISP2312, irq 24, iobase 0xf88cc000
qla2xxx 0000:02:0a.0: Configuring PCI space...
qla2xxx 0000:02:0a.0: Configure NVRAM parameters...
qla2xxx 0000:02:0a.0: Verifying loaded RISC code...
qla2xxx 0000:02:0a.0: Allocated (412 KB) for firmware dump...
scsi3 : qla2xxx
qla2xxx 0000:02:0a.0: LIP reset occured (f8f7).
qla2xxx 0000:02:0a.0: LIP occured (f8f7).
qla2xxx 0000:02:0a.0: LOOP UP detected (1 Gbps).
scsi 3:0:0:0: Direct-Access SEAGATE ST314680 CLAR146 7A0A PQ: 0 ANSI: 3
sd 3:0:0:0: [sdd] 286749476 512-byte hardware sectors (146816 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: a7 00 10 08
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 3:0:0:0: [sdd] 286749476 512-byte hardware sectors (146816 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: a7 00 10 08
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
sdd:<6>qla2xxx 0000:02:0a.0:
QLogic Fibre Channel HBA Driver: 8.02.00-k9
QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel
ISP2312: PCI (66 MHz) @ 0000:02:0a.0 hdma-, host#=3, fw=3.03.20 IPX
unknown partition table
sd 3:0:0:0: [sdd] Attached SCSI disk
sd 3:0:0:0: Attached scsi generic sg4 type 0
sd 3:0:0:0: Embedded Enclosure Device
sd 3:0:0:0: Failed to get diagnostic page 0x6000000
sd 3:0:0:0: Failed to bind enclosure -19
scsi 3:0:1:0: Direct-Access SEAGATE ST314680 CLAR146 7A04 PQ: 0 ANSI: 3
sd 3:0:1:0: [sde] 286749476 512-byte hardware sectors (146816 MB)
sd 3:0:1:0: [sde] Write Protect is off
sd 3:0:1:0: [sde] Mode Sense: a7 00 10 08
sd 3:0:1:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 3:0:1:0: [sde] 286749476 512-byte hardware sectors (146816 MB)
sd 3:0:1:0: [sde] Write Protect is off
sd 3:0:1:0: [sde] Mode Sense: a7 00 10 08
sd 3:0:1:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
sde: unknown partition table
sd 3:0:1:0: [sde] Attached SCSI disk
sd 3:0:1:0: Attached scsi generic sg5 type 0
sd 3:0:1:0: Embedded Enclosure Device
sd 3:0:1:0: Failed to get diagnostic page 0x6000000
sd 3:0:1:0: Failed to bind enclosure -19
scsi 3:0:2:0: Direct-Access SEAGATE ST314680 CLAR146 7A0A PQ: 0 ANSI: 3
sd 3:0:2:0: [sdf] 286749476 512-byte hardware sectors (146816 MB)
sd 3:0:2:0: [sdf] Write Protect is off
sd 3:0:2:0: [sdf] Mode Sense: a7 00 10 08
sd 3:0:2:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 3:0:2:0: [sdf] 286749476 512-byte hardware sectors (146816 MB)
sd 3:0:2:0: [sdf] Write Protect is off
sd 3:0:2:0: [sdf] Mode Sense: a7 00 10 08
sd 3:0:2:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
sdf: unknown partition table
sd 3:0:2:0: [sdf] Attached SCSI disk
sd 3:0:2:0: Attached scsi generic sg6 type 0
sd 3:0:2:0: Embedded Enclosure Device
qla2xxx 0000:02:0a.0: scsi(3:2:0): Abort command issued -- 1 62 2002.
qla2xxx 0000:02:0a.0: scsi(3:2:0): Abort command issued -- 1 6d 2002.
--
Gerhard Mack
gmack@innerfire.net
<>< As a computer I find your faith in technology amusing.
--
