> On Thu, Apr 17, 2008 at 01:07:27PM +0200, Ingo Molnar wrote:
> >
> > * Jack Steiner <steiner@sgi.com> wrote:
> >
> > > Increase the maximum number of apics when running very large
> > > configurations. This patch has no affect on most systems.
> >
> > x86.git overnight random-qa testing found a boot crash and i bisected it
> > down to this patch. The config is:
> >
> >
http://redhat.com/~mingo/misc/config-Thu_Apr_17_10_17_14_CEST_2008.bad
> >
> > the failure is attached below. (I needed the exact boot parameters
> > listed in that bootup log to see this failure.)
> >
> > it seems to be CONFIG_MAXSMP=y triggers the new more-apic-ids code and
> > that causes some breakage elsewhere. [btw., this again shows how useful
> > the CONFIG_MAXSMP debug feature is!]
> >
> > Ingo
> >
> > [ 0.000000] Linux version 2.6.25-rc9-sched-devel.git-x86-latest.git (mingo@dione) (gcc version 4.2.3) #260 SMP Thu Apr 17 10:58:11 CEST 2008
> > [ 0.000000] Command line: root=/dev/sda6 console=ttyS0,115200 earlyprintk=serial,ttyS0,115200 debug initcall_debug apic=verbose sysrq_always_enabled ignore_loglevel selinux=0 nmi_watchdog=2 profile=0 nosmp highres=0 nolapic_timer hpet=disable idle=poll highmem=512m nopat acpi=off
> > [ 0.000000] BIOS-provided physical RAM map:
>
> Has anyone seen this failure?? (Using git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86.git
> from 4/18 AM).
>
> I tried to reproduce the above failure on a small system & was not successful.
>
> Switched to a larger system (XE310 Intel-based 8p, 6GB). All attempts to boot fail
> with the following. I backed out the MAX_APIC change, & changed NR_CPUS=8. Still fails.
>
> ...
> [ 32.010000] ehci_hcd 0000:00:1d.7: port 6 high speed
> [ 32.010000] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
> [ 32.054003] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
> [ 32.058003] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> [ 32.062003] usb usb2: Product: UHCI Host Controller
> [ 32.066004] usb usb2: Manufacturer: Linux 2.6.25-x86-latest.git uhci_hcd
> [ 32.070004] usb usb2: SerialNumber: 0000:00:1d.0
> [ 32.074004] PCI: Found IRQ 10 for device 0000:00:1d.1
> [ 32.078004] PCI: Sharing IRQ 10 with 0000:00:1f.2
> [ 32.082005] PCI: Sharing IRQ 10 with 0000:00:1f.3
> [ 32.086005] PCI: Sharing IRQ 10 with 0000:04:00.1
> [ 32.090005] PCI: Setting latency timer of device 0000:00:1d.1 to 64
> [ 32.094005] uhci_hcd 0000:00:1d.1: UHCI Host Controller
> [ 32.098006] usb 1-6: new high speed USB device using ehci_hcd and address 2
> [ 32.102006] nommu_map_single: overflow 1af757720+8
>
> Full log:
>
>
> [ 0.000000] Linux version 2.6.25-x86-latest.git (root@cleopatra1) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-52)) #2 SMP Fri Apr 18 09:36:33 CDT 2008
> [ 0.000000] Command line: root=/dev/sda2 console=ttyS1,38400n8 debug initcall_debug apic=verbose sysrq_always_enabled ignore_loglevel selinux=0 nmi_watchdog=2 profile=0 nosmp highres=0 nolapic_timer hpet=disable idle=poll highmem=512m nopat acpi=off
