Home » Mailing list archives » linux-kernel » 2008 » March » 19

Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.24.3

!MAILaRCHIVE_VOTE_RePLACE
Previous message: [thread] [date] [author]
Next message: [thread] [date] [author]
[view in full thread]
From: Volker Armin Hemmann <volker.armin.hemmann@...>
To: Tejun Heo <htejun@...>
Cc: <linux-kernel@...>, <linux-ide@...>
Subject: Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.24.3
Date: Wednesday, March 19, 2008 - 3:53 am

Hi,
On Mittwoch, 19. M=E4rz 2008, Tejun Heo wrote:


I tried your patch (on freshly unpacked sources).

non-raid setting in bios,

coldboot:

[   37.123980] ahci 0000:00:0a.0: version 3.0
[   37.124155] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
[   37.124199] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23=
=20
(level, low) -> IRQ 23
[   37.124533] ahci 0000:00:0a.0: controller can't do PMP, turning off CAP_=
PMP
[   38.124731] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x=
f=20
impl IDE mode
[   38.124780] ahci 0000:00:0a.0: flags: 64bit sntf led clo pio
[   38.124819] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[   38.125020] scsi0 : ahci
[   38.125116] scsi1 : ahci
[   38.125182] scsi2 : ahci
[   38.125248] scsi3 : ahci
[   38.125337] ata1: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc10=
0=20
irq 315
[   38.125384] ata2: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc18=
0=20
irq 315
[   38.125432] ata3: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc20=
0=20
irq 315
[   38.125479] ata4: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc28=
0=20
irq 315
[   38.597035] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   38.597732] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133
[   38.597775] ata1.00: 312581808 sectors, multi 16: LBA48
[   38.598405] ata1.00: configured for UDMA/133
[   39.069342] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   39.084225] ata2.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7
[   39.084264] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[   39.086268] ata2.00: configured for UDMA/133
[   39.405277] ata3: SATA link down (SStatus 0 SControl 300)
[   39.724583] ata4: SATA link down (SStatus 0 SControl 300)
[   39.724672] scsi 0:0:0:0: Direct-Access     ATA      WDC WD1600JS-00M 10=
=2E0=20
PQ: 0 ANSI: 5
[   39.724782] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (16004=
2=20
MB)
[   39.724826] sd 0:0:0:0: [sda] Write Protect is off
[   39.724864] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   39.724872] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,=
=20
doesn't support DPO or FUA
[   39.724942] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (16004=
2=20
MB)
[   39.724985] sd 0:0:0:0: [sda] Write Protect is off
[   39.725023] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   39.725030] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,=
=20
doesn't support DPO or FUA
[   39.725079]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[   39.763787] sd 0:0:0:0: [sda] Attached SCSI disk
[   39.763923] scsi 1:0:0:0: Direct-Access     ATA      SAMSUNG HD501LJ  CR=
10=20
PQ: 0 ANSI: 5
[   39.764032] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (50010=
8=20
MB)
[   39.764077] sd 1:0:0:0: [sdb] Write Protect is off
[   39.764115] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   39.764124] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,=
=20
doesn't support DPO or FUA
[   39.764194] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (50010=
8=20
MB)
[   39.764237] sd 1:0:0:0: [sdb] Write Protect is off
[   39.764275] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   39.764283] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,=
=20
doesn't support DPO or FUA
[   39.764332]  sdb: sdb1 sdb2
[   39.793043] sd 1:0:0:0: [sdb] Attached SCSI disk

reboot:
[   39.522696] ahci 0000:00:0a.0: version 3.0
[   39.522871] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
[   39.522914] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23=
=20
(level, low) -> IRQ 23
[   39.523247] ahci 0000:00:0a.0: controller can't do PMP, turning off CAP_=
PMP
[   40.523447] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x=
f=20
impl IDE mode
[   40.523496] ahci 0000:00:0a.0: flags: 64bit sntf led clo pio
[   40.523535] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[   40.523737] scsi0 : ahci
[   40.523832] scsi1 : ahci
[   40.523898] scsi2 : ahci
[   40.523964] scsi3 : ahci
[   40.524053] ata1: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc10=
0=20
irq 315
[   40.524100] ata2: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc18=
0=20
irq 315
[   40.524148] ata3: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc20=
0=20
irq 315
[   40.524195] ata4: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc28=
0=20
irq 315
[   40.995751] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   40.996374] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133
[   40.996416] ata1.00: 312581808 sectors, multi 16: LBA48
[   40.997049] ata1.00: configured for UDMA/133
[   41.468058] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   41.471873] ata2.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7
[   41.471913] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[   41.473917] ata2.00: configured for UDMA/133
[   41.790689] ata3: SATA link down (SStatus 0 SControl 300)
[   42.109995] ata4: SATA link down (SStatus 0 SControl 300)
[   42.110084] scsi 0:0:0:0: Direct-Access     ATA      WDC WD1600JS-00M 10=
=2E0=20
PQ: 0 ANSI: 5
[   42.110194] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (16004=
2=20
MB)
[   42.110238] sd 0:0:0:0: [sda] Write Protect is off
[   42.110276] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   42.110284] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,=
=20
doesn't support DPO or FUA
[   42.110354] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (16004=
2=20
MB)
[   42.110397] sd 0:0:0:0: [sda] Write Protect is off
[   42.110435] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   42.110442] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,=
=20
doesn't support DPO or FUA
[   42.110492]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[   42.140153] sd 0:0:0:0: [sda] Attached SCSI disk
[   42.140289] scsi 1:0:0:0: Direct-Access     ATA      SAMSUNG HD501LJ  CR=
10=20
PQ: 0 ANSI: 5
[   42.140398] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (50010=
8=20
MB)
[   42.140443] sd 1:0:0:0: [sdb] Write Protect is off
[   42.140481] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   42.140489] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,=
=20
doesn't support DPO or FUA
[   42.140559] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (50010=
8=20
MB)
[   42.140602] sd 1:0:0:0: [sdb] Write Protect is off
[   42.140639] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   42.140647] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,=
=20
doesn't support DPO or FUA
[   42.140696]  sdb: sdb1 sdb2
[   42.167607] sd 1:0:0:0: [sdb] Attached SCSI disk

=46ull dmesgs attached.

Gl=FCck Auf
Volker
Previous message: [thread] [date] [author]
Next message: [thread] [date] [author]
Messages in current thread:
2.6.24.X: SATA/AHCI related boot delay., Volker Armin Hemmann, (Sun Mar 9, 2:22 pm)
Re: 2.6.24.X: SATA/AHCI related boot delay., Tejun Heo, (Mon Mar 10, 9:05 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Mon Mar 17, 3:16 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Tue Mar 18, 3:36 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Tue Mar 18, 6:59 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Tue Mar 18, 8:56 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Tue Mar 18, 9:33 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Tue Mar 18, 11:26 pm)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Tue Mar 18, 11:27 pm)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Wed Mar 19, 3:53 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Wed Mar 19, 4:58 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Wed Mar 19, 6:08 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Wed Mar 19, 7:43 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Thu Mar 27, 12:40 pm)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Wed Mar 19, 9:55 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Tue Apr 1, 11:57 pm)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Wed Apr 2, 1:09 pm)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Wed Apr 2, 9:48 pm)
RE: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Peer Chen, (Thu Apr 3, 6:44 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Fri Apr 11, 2:06 am)
RE: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Peer Chen, (Fri Apr 11, 5:50 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Fri Apr 11, 7:46 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Thu Apr 3, 1:04 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Thu Apr 3, 1:26 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Thu Apr 3, 7:47 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Fri Apr 11, 2:05 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Fri Apr 11, 7:55 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Fri Apr 11, 9:27 pm)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Jeff Garzik, (Fri Apr 11, 9:42 pm)
RE: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Peer Chen, (Mon Apr 14, 12:02 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Mon Apr 14, 2:41 am)
RE: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Peer Chen, (Mon Apr 14, 4:11 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Mon Apr 14, 5:12 pm)
RE: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Peer Chen, (Tue Apr 15, 8:57 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Tue Apr 15, 12:20 pm)
RE: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Peer Chen, (Fri Apr 18, 1:51 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Sat Apr 19, 9:48 am)
RE: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Peer Chen, (Tue Apr 22, 6:10 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Tue Apr 22, 8:44 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Tue Apr 22, 10:11 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Hemmann, Volker Armin, (Thu May 29, 10:54 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Fri May 30, 12:19 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Hemmann, Volker Armin, (Fri May 30, 6:43 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Fri May 30, 8:49 pm)
RE: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Peer Chen, (Tue Jun 3, 3:56 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Mon Jun 9, 5:17 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Tejun Heo, (Mon Jun 9, 5:43 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Hemmann, Volker Armin, (Mon Jun 9, 10:49 am)
Re: 2.6.24.X: SATA/AHCI related boot delay. - not with 2.6.2..., Volker Armin Hemmann, (Tue Apr 22, 11:12 am)
Re: 2.6.24.X: SATA/AHCI related boot delay., Volker Armin Hemmann, (Sun Mar 16, 4:34 am)
Re: 2.6.24.X: SATA/AHCI related boot delay., Volker Armin Hemmann, (Mon Mar 10, 12:57 pm)