login
Search
--MP_/uwDr7YIlll9z10iQ/=b7nI_ Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: quoted-printable Content-Disposition: inline Hello, on one of my machines neither 2.6.24 nor 2.6.24.1 work. The system is 64bit on Athlon X2 and ATI-Chipset (SB600). Extract from the kernel messages during boot: [ 66.943103] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32= bit [ 66.950374] ahci 0000:00:12.0: controller can't do PMP, turning off CAP_= PMP [ 67.956470] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x= f impl SATA mode [ 67.964996] ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pio slum = part [ 67.972820] scsi0 : ahci [ 67.975699] scsi1 : ahci [ 67.978445] scsi2 : ahci [ 67.981178] scsi3 : ahci [ 67.983949] ata1: SATA max UDMA/133 abar m1024@0xfadffc00 port 0xfadffd0= 0 irq 509 [ 67.991825] ata2: SATA max UDMA/133 abar m1024@0xfadffc00 port 0xfadffd8= 0 irq 509 [ 67.999729] ata3: SATA max UDMA/133 abar m1024@0xfadffc00 port 0xfadffe0= 0 irq 509 [ 68.007619] ata4: SATA max UDMA/133 abar m1024@0xfadffc00 port 0xfadffe8= 0 irq 509 [ 68.470669] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 98.431945] ata1.00: qc timeout (cmd 0xec) [ 98.454907] ata1.00: failed to IDENTIFY (I/O error, err_mask=3D0x4) [ 98.461296] ata1: failed to recover some devices, retrying in 5 secs [ 103.916773] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 133.878045] ata1.00: qc timeout (cmd 0xec) [ 133.882371] ata1.00: failed to IDENTIFY (I/O error, err_mask=3D0x4) [ 133.888797] ata1: failed to recover some devices, retrying in 5 secs [ 139.343901] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 169.305174] ata1.00: qc timeout (cmd 0xec) [ 169.309534] ata1.00: failed to IDENTIFY (I/O error, err_mask=3D0x4) [ 169.315926] ata1: failed to recover some devices, retrying in 5 secs [ 174.771030] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) The complete boot-log (captured via serial console), lspci output, output of hdparm -I and the kernel config are attached. The PC has one IDE-drive and four SATA-drives (see hdparm.txt). If I wait long enough, the IDE-drive get's recognized and I can continue the boot process, but the SATA-drives are never recognized. The system work's fine with kernel 2.6.23.11 (later kernels not tested). I hope someone can help ... Regards --=20 --------------------------------------- Malte Schr=C3=B6der MalteSch@gmx.de ICQ# 68121508 --------------------------------------- --MP_/uwDr7YIlll9z10iQ/=b7nI_ Content-Type: text/plain; name=lspci.txt Content-Transfer-Encoding: quoted-printable Content-Disposition: attachment; filename=lspci.txt 00:00.0 Host bridge: ATI Technologies Inc RD580 [CrossFire Xpress 3200] Chi= pset Host Bridge 00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:05.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 13) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Hyp= erTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Add= ress Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRA= M Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Mis= cellaneous Control 01:00.0 Ethernet controller: Intel Corporation 82572EI Gigabit Ethernet Con= troller (Copper) (rev 06) 02:00.0 SATA controller: JMicron Technologies, Inc. JMicron 20360/20363 AHC= I Controller (rev 02) 03:01.0 VGA compatible controller: Matrox Graphics, Inc. MGA 1064SG [Mystiq= ue] (rev 02) 03:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Control= ler (rev c0) 03:04.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit = Ethernet Controller (rev 13) # = root@hades ~ # lspci -vvv 00:00.0 Host bridge: ATI Technologies Inc RD580 [CrossFire Xpress 3200] Chi= pset Host Bridge Subsystem: ATI Technologies Inc RD580 [CrossFire Xpress 3200] Chipset Host= Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort+ >SERR- <PERR- INTx- Latency: 0 00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Norm= al decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=3D00, secondary=3D01, subordinate=3D01, sec-latency=3D0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fae00000-faefffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=3D0mA PME(D0+,D1-,D2-,D3hot+,D3col= d+) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- Capabilities: [58] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE- FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, = L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt-= ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable+ Address: fee0300c Data: 4149 Capabilities: [b0] Subsystem: ATI Technologies Inc Unknown device 5952 Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: pcieport-driver 00:05.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Norm= al decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=3D00, secondary=3D02, subordinate=3D02, sec-latency=3D0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: faf00000-faffffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=3D0mA PME(D0+,D1-,D2-,D3hot+,D3col= d+) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- Capabilities: [58] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE- FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, = L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt-= ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable+ Address: fee0300c Data: 4151 Capabilities: [b0] Subsystem: ATI Technologies Inc Unknown device 5952 Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: pcieport-driver 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA (prog-i= f 01 [AHCI 1.0]) Subsystem: ASUSTeK Computer Inc. Unknown device 8232 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 96, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 509 Region 0: I/O ports at b000 [size=3D8] Region 1: I/O ports at a000 [size=3D4] Region 2: I/O ports at 9000 [size=3D8] Region 3: I/O ports at 8000 [size=3D4] Region 4: I/O ports at 7000 [size=3D16] Region 5: Memory at fadffc00 (32-bit, non-prefetchable) [size=3D1K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=3D0mA PME(D0-,D1-,D2-,D3hot-,D3col= d-) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=3D0/2 = Enable+ Address: 00000000fee0300c Data: 4169 Capabilities: [70] SATA HBA <?> Kernel driver in use: ahci Kernel modules: ahci 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) (prog-if 10 = [OHCI]) Subsystem: ATI Technologies Inc SB600 USB (OHCI0) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fadfe000 (32-bit, non-prefetchable) [size=3D4K] Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable- Address: 00000000 Data: 0000 Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) (prog-if 10 = [OHCI]) Subsystem: ATI Technologies Inc SB600 USB (OHCI1) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: Memory at fadfd000 (32-bit, non-prefetchable) [size=3D4K] Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable- Address: 00000000 Data: 0000 Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) (prog-if 10 = [OHCI]) Subsystem: ATI Technologies Inc SB600 USB (OHCI2) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin C routed to IRQ 18 Region 0: Memory at fadfc000 (32-bit, non-prefetchable) [size=3D4K] Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable- Address: 00000000 Data: 0000 Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) (prog-if 10 = [OHCI]) Subsystem: ATI Technologies Inc SB600 USB (OHCI3) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: Memory at fadf7000 (32-bit, non-prefetchable) [size=3D4K] Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable- Address: 00000000 Data: 0000 Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) (prog-if 10 = [OHCI]) Subsystem: ATI Technologies Inc SB600 USB (OHCI4) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin C routed to IRQ 18 Region 0: Memory at fadf6000 (32-bit, non-prefetchable) [size=3D4K] Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable- Address: 00000000 Data: 0000 Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) (p= rog-if 20 [EHCI]) Subsystem: ATI Technologies Inc SB600 USB Controller (EHCI) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin D routed to IRQ 19 Region 0: Memory at fadff800 (32-bit, non-prefetchable) [size=3D256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=3D0mA PME(D0+,D1+,D2+,D3hot+,D3col= d-) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- Bridge: PM- B3+ Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable- Address: 00000000 Data: 0000 Capabilities: [e4] Debug port: BAR=3D1 offset=3D00e0 Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 13) Subsystem: ASUSTeK Computer Inc. Unknown device 4385 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Region 0: I/O ports at 0b00 [size=3D16] Region 1: Memory at fed00000 (32-bit, non-prefetchable) [size=3D1K] Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+ 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE (prog-if 8a [Master S= ecP PriP]) Subsystem: ATI Technologies Inc SB600 IDE Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=3D8] Region 1: I/O ports at 03f4 [size=3D1] Region 2: I/O ports at 0170 [size=3D8] Region 3: I/O ports at 0374 [size=3D1] Region 4: I/O ports at ff00 [size=3D16] Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable- Address: 00000000 Data: 0000 Kernel driver in use: pata_atiixp Kernel modules: pata_atiixp 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia Subsystem: ATI Technologies Inc SBx00 Azalia Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dslow >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin ? routed to IRQ 16 Region 0: Memory at fadf0000 (64-bit, non-prefetchable) [size=3D16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=3D55mA PME(D0+,D1-,D2-,D3hot+,D3co= ld+) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=3D0/0 = Enable- Address: 0000000000000000 Data: 0000 Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge Subsystem: ATI Technologies Inc SB600 PCI to LPC Bridge Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 0 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (prog-if 0= 1 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64 Bus: primary=3D00, secondary=3D03, subordinate=3D03, sec-latency=3D64 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fb000000-fbffffff Prefetchable memory behind bridge: f9800000-f9ffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Hyp= erTransport Technology Configuration Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- Capabilities: [80] HyperTransport: Host or Secondary Interface !!! Possibly incomplete decoding Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=3D0 Link Config: MLWI=3D16bit MLWO=3D16bit LWI=3D16bit LWO=3D16bit Revision ID: 1.02 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Add= ress Map Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRA= M Controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Mis= cellaneous Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp Kernel modules: k8temp 01:00.0 Ethernet controller: Intel Corporation 82572EI Gigabit Ethernet Con= troller (Copper) (rev 06) Subsystem: Intel Corporation PRO/1000 PT Desktop Adapter Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at faee0000 (32-bit, non-prefetchable) [size=3D128K] Region 1: Memory at faec0000 (32-bit, non-prefetchable) [size=3D128K] Region 2: I/O ports at cc00 [size=3D32] Expansion ROM at faea0000 [disabled] [size=3D128K] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=3D0mA PME(D0+,D1-,D2-,D3hot+,D3col= d+) Status: D0 PME-Enable- DSel=3D0 DScale=3D1 PME- Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=3D0/0 = Enable- Address: 0000000000000000 Data: 0000 Capabilities: [e0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <4us, L1 <= 64us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt-= ABWMgmt- Kernel driver in use: e1000 Kernel modules: e1000 02:00.0 SATA controller: JMicron Technologies, Inc. JMicron 20360/20363 AHC= I Controller (rev 02) (prog-if 01 [AHCI 1.0]) Subsystem: ASUSTeK Computer Inc. Unknown device 8202 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at dc00 [size=3D8] Region 1: I/O ports at d880 [size=3D4] Region 2: I/O ports at d800 [size=3D8] Region 3: I/O ports at d480 [size=3D4] Region 4: I/O ports at d400 [size=3D16] Region 5: Memory at faffe000 (32-bit, non-prefetchable) [size=3D8K] Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=3D0mA PME(D0-,D1-,D2-,D3hot+,D3col= d-) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- Capabilities: [50] Express (v1) Legacy Endpoint, MSI 01 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <1us, L1 <= 16us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt-= ABWMgmt- Kernel driver in use: ahci Kernel modules: ahci 03:01.0 VGA compatible controller: Matrox Graphics, Inc. MGA 1064SG [Mystiq= ue] (rev 02) (prog-if 00 [VGA controller]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng+ SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 9 Region 0: Memory at fbffc000 (32-bit, non-prefetchable) [size=3D16K] Region 1: Memory at f9800000 (32-bit, prefetchable) [size=3D8M] Region 2: Memory at fb000000 (32-bit, non-prefetchable) [size=3D8M] Expansion ROM at fb820000 [disabled] [size=3D64K] 03:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Control= ler (rev c0) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Unknown device 81fe Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64 (8000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 3 Region 0: Memory at fbffb800 (32-bit, non-prefetchable) [size=3D2K] Region 1: I/O ports at ec00 [size=3D128] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2+ AuxCurrent=3D0mA PME(D0-,D1-,D2+,D3hot+,D3col= d+) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- 03:04.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit = Ethernet Controller (rev 13) Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet Controll= er (Asus) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 23 Region 0: Memory at fbff4000 (32-bit, non-prefetchable) [size=3D16K] Region 1: I/O ports at e800 [size=3D256] Expansion ROM at fb800000 [disabled] [size=3D128K] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=3D0mA PME(D0+,D1+,D2+,D3hot+,D3col= d+) Status: D0 PME-Enable- DSel=3D0 DScale=3D1 PME- Capabilities: [50] Vital Product Data <?> Kernel driver in use: skge Kernel modules: skge # = root@hades ~ # lspci -vvvn 00:00.0 0600: 1002:5952 Subsystem: 1002:5952 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort+ >SERR- <PERR- INTx- Latency: 0 00:04.0 0604: 1002:5a36 (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=3D00, secondary=3D01, subordinate=3D01, sec-latency=3D0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fae00000-faefffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=3D0mA PME(D0+,D1-,D2-,D3hot+,D3col= d+) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- Capabilities: [58] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE- FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, = L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt-= ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable+ Address: fee0300c Data: 4149 Capabilities: [b0] Subsystem: 1002:5952 Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: pcieport-driver 00:05.0 0604: 1002:5a37 (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=3D00, secondary=3D02, subordinate=3D02, sec-latency=3D0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: faf00000-faffffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=3D0mA PME(D0+,D1-,D2-,D3hot+,D3col= d+) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- Capabilities: [58] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ RBE- FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, = L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt-= ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable+ Address: fee0300c Data: 4151 Capabilities: [b0] Subsystem: 1002:5952 Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: pcieport-driver 00:12.0 0106: 1002:4380 (prog-if 01 [AHCI 1.0]) Subsystem: 1043:8232 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 96, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 509 Region 0: I/O ports at b000 [size=3D8] Region 1: I/O ports at a000 [size=3D4] Region 2: I/O ports at 9000 [size=3D8] Region 3: I/O ports at 8000 [size=3D4] Region 4: I/O ports at 7000 [size=3D16] Region 5: Memory at fadffc00 (32-bit, non-prefetchable) [size=3D1K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=3D0mA PME(D0-,D1-,D2-,D3hot-,D3col= d-) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=3D0/2 = Enable+ Address: 00000000fee0300c Data: 4169 Capabilities: [70] SATA HBA <?> Kernel driver in use: ahci Kernel modules: ahci 00:13.0 0c03: 1002:4387 (prog-if 10 [OHCI]) Subsystem: 1002:4387 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fadfe000 (32-bit, non-prefetchable) [size=3D4K] Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable- Address: 00000000 Data: 0000 Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.1 0c03: 1002:4388 (prog-if 10 [OHCI]) Subsystem: 1002:4388 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: Memory at fadfd000 (32-bit, non-prefetchable) [size=3D4K] Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable- Address: 00000000 Data: 0000 Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.2 0c03: 1002:4389 (prog-if 10 [OHCI]) Subsystem: 1002:4389 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin C routed to IRQ 18 Region 0: Memory at fadfc000 (32-bit, non-prefetchable) [size=3D4K] Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable- Address: 00000000 Data: 0000 Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.3 0c03: 1002:438a (prog-if 10 [OHCI]) Subsystem: 1002:438a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: Memory at fadf7000 (32-bit, non-prefetchable) [size=3D4K] Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable- Address: 00000000 Data: 0000 Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.4 0c03: 1002:438b (prog-if 10 [OHCI]) Subsystem: 1002:438b Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin C routed to IRQ 18 Region 0: Memory at fadf6000 (32-bit, non-prefetchable) [size=3D4K] Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable- Address: 00000000 Data: 0000 Kernel driver in use: ohci_hcd Kernel modules: ohci-hcd 00:13.5 0c03: 1002:4386 (prog-if 20 [EHCI]) Subsystem: 1002:4386 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin D routed to IRQ 19 Region 0: Memory at fadff800 (32-bit, non-prefetchable) [size=3D256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=3D0mA PME(D0+,D1+,D2+,D3hot+,D3col= d-) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- Bridge: PM- B3+ Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable- Address: 00000000 Data: 0000 Capabilities: [e4] Debug port: BAR=3D1 offset=3D00e0 Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:14.0 0c05: 1002:4385 (rev 13) Subsystem: 1043:4385 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Region 0: I/O ports at 0b00 [size=3D16] Region 1: Memory at fed00000 (32-bit, non-prefetchable) [size=3D1K] Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+ 00:14.1 0101: 1002:438c (prog-if 8a [Master SecP PriP]) Subsystem: 1002:438c Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=3D8] Region 1: I/O ports at 03f4 [size=3D1] Region 2: I/O ports at 0170 [size=3D8] Region 3: I/O ports at 0374 [size=3D1] Region 4: I/O ports at ff00 [size=3D16] Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=3D0/0 = Enable- Address: 00000000 Data: 0000 Kernel driver in use: pata_atiixp Kernel modules: pata_atiixp 00:14.2 0403: 1002:4383 Subsystem: 1002:4383 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dslow >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin ? routed to IRQ 16 Region 0: Memory at fadf0000 (64-bit, non-prefetchable) [size=3D16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=3D55mA PME(D0+,D1-,D2-,D3hot+,D3co= ld+) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=3D0/0 = Enable- Address: 0000000000000000 Data: 0000 Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:14.3 0601: 1002:438d Subsystem: 1002:438d Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 0 00:14.4 0604: 1002:4384 (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64 Bus: primary=3D00, secondary=3D03, subordinate=3D03, sec-latency=3D64 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fb000000-fbffffff Prefetchable memory behind bridge: f9800000-f9ffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:18.0 0600: 1022:1100 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- Capabilities: [80] HyperTransport: Host or Secondary Interface !!! Possibly incomplete decoding Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=3D0 Link Config: MLWI=3D16bit MLWO=3D16bit LWI=3D16bit LWO=3D16bit Revision ID: 1.02 00:18.1 0600: 1022:1101 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- 00:18.2 0600: 1022:1102 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- 00:18.3 0600: 1022:1103 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp Kernel modules: k8temp 01:00.0 0200: 8086:10b9 (rev 06) Subsystem: 8086:1083 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at faee0000 (32-bit, non-prefetchable) [size=3D128K] Region 1: Memory at faec0000 (32-bit, non-prefetchable) [size=3D128K] Region 2: I/O ports at cc00 [size=3D32] Expansion ROM at faea0000 [disabled] [size=3D128K] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=3D0mA PME(D0+,D1-,D2-,D3hot+,D3col= d+) Status: D0 PME-Enable- DSel=3D0 DScale=3D1 PME- Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=3D0/0 = Enable- Address: 0000000000000000 Data: 0000 Capabilities: [e0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <4us, L1 <= 64us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt-= ABWMgmt- Kernel driver in use: e1000 Kernel modules: e1000 02:00.0 0106: 197b:2360 (rev 02) (prog-if 01 [AHCI 1.0]) Subsystem: 1043:8202 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dfast >TAbort- <TAbort- = <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at dc00 [size=3D8] Region 1: I/O ports at d880 [size=3D4] Region 2: I/O ports at d800 [size=3D8] Region 3: I/O ports at d480 [size=3D4] Region 4: I/O ports at d400 [size=3D16] Region 5: Memory at faffe000 (32-bit, non-prefetchable) [size=3D8K] Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=3D0mA PME(D0-,D1-,D2-,D3hot+,D3col= d-) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- Capabilities: [50] Express (v1) Legacy Endpoint, MSI 01 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <1us, L1 <= 16us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt-= ABWMgmt- Kernel driver in use: ahci Kernel modules: ahci 03:01.0 0300: 102b:051a (rev 02) (prog-if 00 [VGA controller]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Steppi= ng+ SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 9 Region 0: Memory at fbffc000 (32-bit, non-prefetchable) [size=3D16K] Region 1: Memory at f9800000 (32-bit, prefetchable) [size=3D8M] Region 2: Memory at fb000000 (32-bit, non-prefetchable) [size=3D8M] Expansion ROM at fb820000 [disabled] [size=3D64K] 03:03.0 0c00: 1106:3044 (rev c0) (prog-if 10 [OHCI]) Subsystem: 1043:81fe Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64 (8000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 3 Region 0: Memory at fbffb800 (32-bit, non-prefetchable) [size=3D2K] Region 1: I/O ports at ec00 [size=3D128] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2+ AuxCurrent=3D0mA PME(D0-,D1-,D2+,D3hot+,D3col= d+) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- 03:04.0 0200: 11ab:4320 (rev 13) Subsystem: 1043:811a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 23 Region 0: Memory at fbff4000 (32-bit, non-prefetchable) [size=3D16K] Region 1: I/O ports at e800 [size=3D256] Expansion ROM at fb800000 [disabled] [size=3D128K] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=3D0mA PME(D0+,D1+,D2+,D3hot+,D3col= d+) Status: D0 PME-Enable- DSel=3D0 DScale=3D1 PME- Capabilities: [50] Vital Product Data <?> Kernel driver in use: skge Kernel modules: skge 2-bit, non-prefetchable) [size=3D2K] Region 1: I/O ports at ec00 [size=3D128] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2+ AuxCurrent=3D0mA PME(D0-,D1-,D2+,D3hot+,D3col= d+) Status: D0 PME-Enable- DSel=3D0 DScale=3D0 PME- 03:04.0 0200: 11ab:4320 (rev 13) Subsystem: 1043:811a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Steppi= ng- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=3Dmedium >TAbort- <TAbort= - <MAbort- >SERR- <PERR- INTx- Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 23 Region 0: Memory at fbff4000 (32-bit, non-prefetchable) [size=3D16K] Region 1: I/O ports at e800 [size=3D256] Expansion ROM at fb800000 [disabled] [size=3D128K] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=3D0mA PME(D0+,D1+,D2+,D3hot+,D3col= d+) Status: D0 PME-Enable- DSel=3D0 DScale=3D1 PME- Capabilities: [50] Vital Product Data <?> Kernel driver in use: skge Kernel modules: skge --MP_/uwDr7YIlll9z10iQ/=b7nI_ Content-Type: text/plain; name=boot.txt Content-Transfer-Encoding: quoted-printable Content-Disposition: attachment; filename=boot.txt [ 0.000000] Linux version 2.6.24.1 (root@highlander) (gcc version 4.2.3 = (Debian 4.2.3-1)) #1 SMP Sat Feb 9 11:07:57 CET 2008 [ 0.000000] Command line: root=3DLABEL=3DROOT ro vga=3Dextended console= =3Dtty0 console=3DttyS0,115200 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 0000000000098000 (usable) [ 0.000000] BIOS-e820: 0000000000098000 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable) [ 0.000000] BIOS-e820: 000000007ffb0000 - 000000007ffbe000 (ACPI data) [ 0.000000] BIOS-e820: 000000007ffbe000 - 000000007ffe0000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved) [ 0.000000] BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved) [ 0.000000] end_pfn_map =3D 1048576 [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP 000FB400, 0024 (r2 ACPIAM) [ 0.000000] ACPI: XSDT 7FFB0100, 005C (r1 NEC 1000709 MSFT = 97) [ 0.000000] ACPI: FACP 7FFB0290, 00F4 (r3 A_M_I_ OEMFACP 1000709 MSFT = 97) [ 0.000000] ACPI: DSDT 7FFB05B0, 7A34 (r1 A0578 A0578000 0 INTL = 20060113) [ 0.000000] ACPI: FACS 7FFBE000, 0040 [ 0.000000] ACPI: APIC 7FFB0390, 005C (r1 A_M_I_ OEMAPIC 1000709 MSFT = 97) [ 0.000000] ACPI: MCFG 7FFB03F0, 003C (r1 A_M_I_ OEMMCFG 1000709 MSFT = 97) [ 0.000000] ACPI: SLIC 7FFB0430, 0176 (r1 NEC 1000709 MSFT = 97) [ 0.000000] ACPI: OEMB 7FFBE040, 0060 (r1 A_M_I_ AMI_OEM 1000709 MSFT = 97) [ 0.000000] ACPI: HPET 7FFB7FF0, 0038 (r1 A_M_I_ OEMHPET 1000709 MSFT = 97) [ 0.000000] ACPI: SSDT 7FFB8030, 0248 (r1 A_M_I_ POWERNOW 1 AMD = 1) [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1048576 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0 -> 152 [ 0.000000] 0: 256 -> 524208 [ 0.000000] ATI board detected. Disabling timer routing over 8254. [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] Processor #1 [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] Setting APIC routing to flat [ 0.000000] ACPI: HPET id: 0x8300 base: 0xfed00000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000= :7f700000) [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 32624 bytes of per cpu data [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Tota= l pages: 516128 [ 0.000000] Kernel command line: root=3DLABEL=3DROOT ro vga=3Dextended c= onsole=3Dtty0 console=3DttyS0,115200 [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] Extended CMOS year: 2000 [ 0.000000] TSC calibrated against HPET [ 64.698527] Marking TSC unstable due to TSCs unsynchronized [ 64.698529] time.c: Detected 2405.448 MHz processor. [ 64.717798] Console: colour VGA+ 80x50 [ 64.717801] console [tty0] enabled [ 64.722885] console [ttyS0] enabled [ 65.067150] Dentry cache hash table entries: 262144 (order: 9, 2097152 b= ytes) [ 65.075705] Inode-cache hash table entries: 131072 (order: 8, 1048576 by= tes) [ 65.083276] Checking aperture... [ 65.086596] CPU 0: aperture @ fede000000 size 32 MB [ 65.091565] Aperture too small (32 MB) [ 65.104495] No AGP bridge found [ 65.123646] Memory: 2057172k/2096832k available (1727k kernel code, 3866= 4k reserved, 832k data, 208k init) [ 65.133447] SLUB: Genslabs=3D11, HWalign=3D64, Order=3D0-1, MinObjects= =3D4, CPUs=3D2, Nodes=3D1 [ 65.200682] Calibrating delay using timer specific routine.. 4813.71 Bog= oMIPS (lpj=3D2406857) [ 65.209255] Mount-cache hash table entries: 256 [ 65.213953] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/= line) [ 65.221183] CPU: L2 Cache: 512K (64 bytes/line) [ 65.225804] CPU: Physical Processor ID: 0 [ 65.229901] CPU: Processor Core ID: 0 [ 65.233673] SMP alternatives: switching to UP code [ 65.240501] ACPI: Core revision 20070126 [ 65.257607] Using local APIC timer interrupts. [ 65.303873] Detected 12.528 MHz APIC timer. [ 65.308504] SMP alternatives: switching to SMP code [ 65.313735] Booting processor 1/2 APIC 0x1 [ 65.328391] Initializing CPU#1 [ 65.388759] Calibrating delay using timer specific routine.. 4810.82 Bog= oMIPS (lpj=3D2405413) [ 65.388765] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/= line) [ 65.388766] CPU: L2 Cache: 512K (64 bytes/line) [ 65.388768] CPU: Physical Processor ID: 0 [ 65.388770] CPU: Processor Core ID: 1 [ 65.388833] AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ stepping 02 [ 65.388438] Brought up 2 CPUs [ 65.429529] net_namespace: 120 bytes [ 65.434696] NET: Registered protocol family 16 [ 65.439321] ACPI: bus type pci registered [ 65.443482] PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved [ 65.450006] PCI: Not using MMCONFIG. [ 65.453666] PCI: Using configuration type 1 [ 65.465629] ACPI: Interpreter enabled [ 65.469380] ACPI: (supports S0 S5) [ 65.473018] ACPI: Using IOAPIC for interrupt routing [ 65.478330] Error attaching device data [ 65.482257] Error attaching device data [ 65.493960] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 65.519948] PCI: Transparent bridge - 0000:00:14.4 [ 65.543144] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15= ) *0, disabled. [ 65.552382] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15= ) *0, disabled. [ 65.563083] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15= ) *0, disabled. [ 65.572305] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15= ) *0, disabled. [ 65.581538] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15= ) *0, disabled. [ 65.590788] ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled. [ 65.597553] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15= ) *0, disabled. [ 65.606785] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15= ) *0, disabled. [ 65.615977] ACPI Warning (tbutils-0217): Incorrect checksum in table [OE= MB] - 0E, should be 05 [20070126] [ 65.627180] Linux Plug and Play Support v0.97 (c) Adam Belay [ 65.632940] pnp: PnP ACPI init [ 65.636085] ACPI: bus type pnp registered [ 65.643944] pnp: PnP ACPI: found 15 devices [ 65.648223] ACPI: ACPI bus type pnp unregistered [ 65.653012] PCI: Using ACPI for IRQ routing [ 65.657285] PCI: If a device doesn't work, try "pci=3Drouteirq". If it = helps, post a report [ 65.669853] DMAR:No DMAR devices found [ 65.673842] Time: hpet clocksource has been installed. [ 65.680913] system 00:06: ioport range 0x4d0-0x4d1 has been reserved [ 65.688638] system 00:06: ioport range 0x40b-0x40b has been reserved [ 65.695080] system 00:06: ioport range 0x4d6-0x4d6 has been reserved [ 65.701527] system 00:06: ioport range 0xc00-0xc01 has been reserved [ 65.707973] system 00:06: ioport range 0xc14-0xc14 has been reserved [ 65.714420] system 00:06: ioport range 0xc50-0xc51 has been reserved [ 65.720865] system 00:06: ioport range 0xc52-0xc52 has been reserved [ 65.727312] system 00:06: ioport range 0xc6c-0xc6c has been reserved [ 65.733758] system 00:06: ioport range 0xc6f-0xc6f has been reserved [ 65.740205] system 00:06: ioport range 0xcd0-0xcd1 has been reserved [ 65.746652] system 00:06: ioport range 0xcd2-0xcd3 has been reserved [ 65.754353] system 00:06: ioport range 0xcd4-0xcd5 has been reserved [ 65.760800] system 00:06: ioport range 0xcd6-0xcd7 has been reserved [ 65.767247] system 00:06: ioport range 0xcd8-0xcdf has been reserved [ 65.773692] system 00:06: ioport range 0x800-0x89f has been reserved [ 65.780138] system 00:06: ioport range 0xb10-0xb1f has been reserved [ 65.786585] system 00:06: ioport range 0x900-0x90f has been reserved [ 65.793033] system 00:06: ioport range 0x910-0x91f has been reserved [ 65.799475] system 00:06: ioport range 0xfe00-0xfefe has been reserved [ 65.806096] system 00:06: iomem range 0xffb80000-0xffbfffff could not be= reserved [ 65.813700] system 00:06: iomem range 0xfff00000-0xffffffff could not be= reserved [ 65.822524] system 00:06: iomem range 0xff600000-0xff60ffff has been res= erved [ 65.829759] system 00:09: iomem range 0xfec00000-0xfec00fff has been res= erved [ 65.836992] system 00:09: iomem range 0xfee00000-0xfee00fff could not be= reserved [ 65.844603] system 00:0b: ioport range 0xe00-0xe0f has been reserved [ 65.851047] system 00:0b: ioport range 0xe80-0xe8f has been reserved [ 65.857492] system 00:0b: ioport range 0xf40-0xf4f has been reserved [ 65.863942] system 00:0b: ioport range 0xa30-0xa3f has been reserved [ 65.870390] system 00:0c: iomem range 0xe0000000-0xefffffff has been res= erved [ 65.877617] system 00:0d: iomem range 0xf0000000-0xf08fffff has been res= erved [ 65.886130] system 00:0e: iomem range 0x0-0x9ffff could not be reserved [ 65.892845] system 00:0e: iomem range 0xc0000-0xcffff has been reserved [ 65.899554] system 00:0e: iomem range 0xe0000-0xfffff could not be reser= ved [ 65.906608] system 00:0e: iomem range 0x100000-0x7fffffff could not be r= eserved [ 65.914035] system 00:0e: iomem range 0x0-0x0 could not be reserved [ 65.920687] PCI: Bridge: 0000:00:04.0 [ 65.924440] IO window: c000-cfff [ 65.927933] MEM window: fae00000-faefffff [ 65.932210] PREFETCH window: disabled. [ 65.936224] PCI: Bridge: 0000:00:05.0 [ 65.939977] IO window: d000-dfff [ 65.944741] MEM window: faf00000-faffffff [ 65.949014] PREFETCH window: disabled. [ 65.953030] PCI: Bridge: 0000:00:14.4 [ 65.956786] IO window: e000-efff [ 65.960280] MEM window: fb000000-fbffffff [ 65.964557] PREFETCH window: f9800000-f9ffffff [ 65.969289] NET: Registered protocol family 2 [ 65.983447] IP route cache hash table entries: 65536 (order: 7, 524288 b= ytes) [ 65.991146] TCP established hash table entries: 262144 (order: 10, 41943= 04 bytes) [ 66.000367] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 66.008808] TCP: Hash tables configured (established 262144 bind 65536) [ 66.015522] TCP reno registered [ 66.021450] checking if image is initramfs... it is [ 66.222261] Freeing initrd memory: 3541k freed [ 66.229213] audit: initializing netlink socket (disabled) [ 66.234715] audit(1202556795.894:1): initialized [ 66.241291] Block layer SCSI generic (bsg) driver version 0.4 loaded (ma= jor 254) [ 66.248835] io scheduler noop registered [ 66.252872] io scheduler deadline registered (default) [ 66.374221] assign_interrupt_mode Found MSI capability [ 66.379547] assign_interrupt_mode Found MSI capability [ 66.406794] Real Time Clock Driver v1.12ac [ 66.411021] Linux agpgart interface v0.102 [ 66.415227] Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sha= ring disabled [ 66.423300] serial8250: ttyS0 at I/O 0x3f8 (irq =3D 4) is a 16550A [ 66.429858] 00:0a: ttyS0 at I/O 0x3f8 (irq =3D 4) is a 16550A [ 66.436053] RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 = blocksize [ 66.443722] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 [ 66.450000] PNP: PS/2 appears to have AUX port disabled, if this is inco= rrect please boot with i8042.nopnp [ 66.459857] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 66.464968] mice: PS/2 mouse device common for all mice [ 66.470318] cpuidle: using governor ladder [ 66.474511] cpuidle: using governor menu [ 66.478550] TCP cubic registered [ 66.481981] BIOS EDD facility v0.16 2004-Jun-25, 6 devices found [ 66.488239] Freeing unused kernel memory: 208k freed Loading, please wait... ^[^[[ 66.513140] input: AT Translated Set 2 keyboard as /devices/platform= /i8042/serio0/input/input0 Begin: Loading essential drivers... ... [ 66.575266] NET: Registered protocol family 1 Done. Begin: Running /scripts/init-premount ... [ 66.631328] ACPI: duty_cycle spans bit 4 [ 66.772225] SCSI subsystem initialized [ 66.776251] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 66.783020] Copyright (c) 1999-2006 Intel Corporation. [ 66.788456] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -=[ 66.844296] e1000: 0000:01:00.0: e1000_check_options: Interrupt Throttli= ng Rate (ints/sec) set to dynamic conservative mode [ 66.856474] e1000: 0000:01:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width= x1) 00:1b:21:04:f5:02 [ 66.891985] Floppy drive(s): fd0 is 1.44M [ 66.898775] usbcore: registered new interface driver usbfs [ 66.904582] usbcore: registered new interface driver hub [ 66.910971] FDC 0 is a post-1991 82077 [ 66.915627] usbcore: registered new device driver usb [ 66.928261] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connecti= on [ 66.935081] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 21 (level, low) -= [ 66.943103] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32= bit [ 66.950374] ahci 0000:00:12.0: controller can't do PMP, turning off CAP_= PMP [ 67.307246] udev: renamed network interface eth0 to eth1 [ 67.956470] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x= f impl SATA mode [ 67.964996] ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pio slum = part [ 67.972820] scsi0 : ahci [ 67.975699] scsi1 : ahci [ 67.978445] scsi2 : ahci [ 67.981178] scsi3 : ahci [ 67.983949] ata1: SATA max UDMA/133 abar m1024@0xfadffc00 port 0xfadffd0= 0 irq 509 [ 67.991825] ata2: SATA max UDMA/133 abar m1024@0xfadffc00 port 0xfadffd8= 0 irq 509 [ 67.999729] ata3: SATA max UDMA/133 abar m1024@0xfadffc00 port 0xfadffe0= 0 irq 509 [ 68.007619] ata4: SATA max UDMA/133 abar m1024@0xfadffc00 port 0xfadffe8= 0 irq 509 [ 68.470669] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 98.431945] ata1.00: qc timeout (cmd 0xec) [ 98.454907] ata1.00: failed to IDENTIFY (I/O error, err_mask=3D0x4) [ 98.461296] ata1: failed to recover some devices, retrying in 5 secs [ 103.916773] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 133.878045] ata1.00: qc timeout (cmd 0xec) [ 133.882371] ata1.00: failed to IDENTIFY (I/O error, err_mask=3D0x4) [ 133.888797] ata1: failed to recover some devices, retrying in 5 secs [ 139.343901] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 169.305174] ata1.00: qc timeout (cmd 0xec) [ 169.309534] ata1.00: failed to IDENTIFY (I/O error, err_mask=3D0x4) [ 169.315926] ata1: failed to recover some devices, retrying in 5 secs [ 174.771030] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 175.232784] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 205.194064] ata2.00: qc timeout (cmd 0xec) [ 205.198424] ata2.00: failed to IDENTIFY (I/O error, err_mask=3D0x4) [ 205.204834] ata2: failed to recover some devices, retrying in 5 secs [ 210.659913] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 240.621188] ata2.00: qc timeout (cmd 0xec) [ 240.625543] ata2.00: failed to IDENTIFY (I/O error, err_mask=3D0x4) [ 240.631935] ata2: failed to recover some devices, retrying in 5 secs [ 246.087042] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Done. Begin: Mounting root file system... ... Begin: Running /scripts/local-top ... Begin: Loading MD modules ... [ 246.499384] xor: automatically using best checksumming function: generic= _sse [ 246.511385] generic_sse: 7332.000 MB/sec [ 246.515867] xor: using function: generic_sse (7332.000 MB/sec) [ 246.522249] async_tx: api initialized (sync-only) [ 246.547341] raid6: int64x1 2187 MB/s [ 246.567319] raid6: int64x2 2863 MB/s [ 246.587285] raid6: int64x4 2679 MB/s [ 246.607266] raid6: int64x8 2359 MB/s [ 246.628217] raid6: sse2x1 3417 MB/s [ 246.648189] raid6: sse2x2 4453 MB/s [ 246.668158] raid6: sse2x4 4605 MB/s [ 246.672126] raid6: using algorithm sse2x4 (4605 MB/s) [ 246.677478] md: raid6 personality registered for level 6 [ 246.683066] md: raid5 personality registered for level 5 [ 246.688675] md: raid4 personality registered for level 4 Success: loaded module raid456. Done. Begin: Assembling all MD arrays ... mdadm: No devices listed in conf file were found. Failure: failed to assemble all arrays. Done. Begin: Executing udevtrigger again ... Done. Done. Begin: Waiting for root file system... ... [ 276.048325] ata2.00: qc timeout (cmd 0xec) [ 276.052689] ata2.00: failed to IDENTIFY (I/O error, err_mask=3D0x4) [ 276.059068] ata2: failed to recover some devices, retrying in 5 secs [ 281.514182] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 281.975740] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 311.936762] ata3.00: qc timeout (cmd 0xec) [ 311.941123] ata3.00: failed to IDENTIFY (I/O error, err_mask=3D0x4) [ 311.947544] ata3: failed to recover some devices, retrying in 5 secs [ 317.402620] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 347.363902] ata3.00: qc timeout (cmd 0xec) [ 347.368261] ata3.00: failed to IDENTIFY (I/O error, err_mask=3D0x4) [ 347.374662] ata3: failed to recover some devices, retrying in 5 secs [ 352.829756] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 382.791027] ata3.00: qc timeout (cmd 0xec) [ 382.795389] ata3.00: failed to IDENTIFY (I/O error, err_mask=3D0x4) [ 382.801766] ata3: failed to recover some devices, retrying in 5 secs [ 388.256887] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 388.718190] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 418.679474] ata4.00: qc timeout (cmd 0xec) [ 418.683838] ata4.00: failed to IDENTIFY (I/O error, err_mask=3D0x4) [ 418.690243] ata4: failed to recover some devices, retrying in 5 secs [ 424.145329] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Done. ALERT! /dev/disk/by-label/ROOT does not exist. Dropping to a shell! Check your root=3D boot argument (cat /proc/cmdline) Check for missing modules (cat /proc/modules), or device files (ls /dev) BusyBox v1.1.3 (Debian 1:1.1
