Home » Mailing list archives » linux-kernel » 2007 » September » 20

Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1]

Previous message: [thread] [date] [author]
Next message: [thread] [date] [author]
[view in full thread]
From: Jiri Slaby
Subject: Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1]
Date: Thursday, September 20, 2007 - 12:24 am

On 09/20/2007 03:51 AM, Dave Airlie wrote:

Maybe you are rather interested in these dmesg lines:
Linux agpgart interface v0.102
agpgart: suspend/resume problematic: resume with 3D/DRI active may lockup X.Org
on some chipset/BIOS combos (see DEBUG_AGP_PM in intel-agp.c)
agpgart: Detected an Intel G33 Chipset.
agpgart: Detected 8192K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized i915 1.6.0 20060119 on minor 0
...
set status page addr 0x00033000
agpgart: pg_start == 0x000005ff,intel_private.gtt_entries == 0x00000800
agpgart: Trying to insert into local/stolen memory

So the problem is, that X passes too low start.

The X log:
http://www.fi.muni.cz/~xslaby/sklad/Xorg.0.log.old

# lspci -vvx
00:00.0 Host bridge: Intel Corporation DRAM Controller (rev 02)
        Subsystem: Intel Corporation DRAM Controller
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
        Latency: 0
        Capabilities: [e0] Vendor Specific Information
00: 86 80 c0 29 06 00 90 20 02 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c0 29
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

00:02.0 VGA compatible controller: Intel Corporation Integrated Graphics
Controller (rev 02) (prog-if 00 [VGA])
        Subsystem: Intel Corporation Integrated Graphics Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at ffa80000 (32-bit, non-prefetchable) [size=512K]
        Region 1: I/O ports at ec00 [size=8]
        Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
        Region 3: Memory at ff900000 (32-bit, non-prefetchable) [size=1M]
        Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
                Address: 00000000  Data: 0000
        Capabilities: [d0] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 c2 29 07 00 90 00 02 00 00 03 00 00 00 00
10: 00 00 a8 ff 01 ec 00 00 08 00 00 d0 00 00 90 ff
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c2 29
30: 00 00 00 00 90 00 00 00 00 00 00 00 0a 01 00 00

00:03.0 Communication controller: Intel Corporation MEI Controller (rev 02)
        Subsystem: Intel Corporation MEI Controller
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at ffa7bc00 (64-bit, non-prefetchable) [size=16]
        Capabilities: [50] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [8c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
                Address: 0000000000000000  Data: 0000
00: 86 80 c4 29 06 00 10 00 02 00 80 07 00 00 80 00
10: 04 bc a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c4 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00

00:03.2 IDE interface: Intel Corporation PT IDER Controller (rev 02) (prog-if 85
[Master SecO PriO])
        Subsystem: Intel Corporation PT IDER Controller
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin C routed to IRQ 12
        Region 0: I/O ports at e880 [size=8]
        Region 1: I/O ports at e800 [size=4]
        Region 2: I/O ports at e480 [size=8]
        Region 3: I/O ports at e400 [size=4]
        Region 4: I/O ports at e080 [size=16]
        Capabilities: [c8] Power Management version 3
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
                Address: 0000000000000000  Data: 0000
00: 86 80 c6 29 05 00 b0 00 02 85 01 01 00 00 00 00
10: 81 e8 00 00 01 e8 00 00 81 e4 00 00 01 e4 00 00
20: 81 e0 00 00 00 00 00 00 00 00 00 00 86 80 c6 29
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0c 03 00 00

00:03.3 Serial controller: Intel Corporation Serial KT Controller (rev 02)
(prog-if 02 [16550])
        Subsystem: Intel Corporation Serial KT Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 17
        Region 0: I/O ports at e000 [size=8]
        Region 1: Memory at ffa7a000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [c8] Power Management version 3
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
                Address: 0000000000000000  Data: 0000
00: 86 80 c7 29 07 00 b0 00 02 02 00 07 00 00 00 00
10: 01 e0 00 00 00 a0 a7 ff 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c7 29
30: 00 00 00 00 c8 00 00 00 00 00 00 00 05 02 00 00

00:19.0 Ethernet controller: Intel Corporation 82566DM-2 Gigabit Network
Connection (rev 02)
        Subsystem: Intel Corporation Unknown device 0000
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 318
        Region 0: Memory at ffa40000 (32-bit, non-prefetchable) [size=128K]
        Region 1: Memory at ffa79000 (32-bit, non-prefetchable) [size=4K]
        Region 2: I/O ports at dc00 [size=32]
        Capabilities: [c8] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable+
                Address: 00000000fee0300c  Data: 4199
        Capabilities: [e0] Vendor Specific Information
00: 86 80 bd 10 07 04 10 00 02 00 00 02 00 00 00 00
10: 00 00 a4 ff 00 90 a7 ff 01 dc 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 00 00
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0f 01 00 00

00:1a.0 USB Controller: Intel Corporation USB UHCI Controller #4 (rev 02)
(prog-if 00 [UHCI])
        Subsystem: Intel Corporation USB UHCI Controller #4
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 4: I/O ports at d880 [size=32]
        Capabilities: [50] Vendor Specific Information
00: 86 80 37 29 05 00 90 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 d8 00 00 00 00 00 00 00 00 00 00 86 80 37 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00

00:1a.1 USB Controller: Intel Corporation USB UHCI Controller #5 (rev 02)
(prog-if 00 [UHCI])
        Subsystem: Intel Corporation USB UHCI Controller #5
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 21
        Region 4: I/O ports at d800 [size=32]
        Capabilities: [50] Vendor Specific Information
00: 86 80 38 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d8 00 00 00 00 00 00 00 00 00 00 86 80 38 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0e 02 00 00

00:1a.2 USB Controller: Intel Corporation USB UHCI Controller #6 (rev 02)
(prog-if 00 [UHCI])
        Subsystem: Intel Corporation USB UHCI Controller #6
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin C routed to IRQ 18
        Region 4: I/O ports at d480 [size=32]
        Capabilities: [50] Vendor Specific Information
00: 86 80 39 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 d4 00 00 00 00 00 00 00 00 00 00 86 80 39 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0c 03 00 00

00:1a.7 USB Controller: Intel Corporation USB2 EHCI Controller #2 (rev 02)
(prog-if 20 [EHCI])
        Subsystem: Intel Corporation USB2 EHCI Controller #2
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin D routed to IRQ 19
        Region 0: Memory at ffa7b400 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Debug port
        Capabilities: [98] Vendor Specific Information
00: 86 80 3c 29 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 b4 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 3c 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 03 04 00 00

00:1b.0 Audio device: Intel Corporation HD Audio Controller (rev 02)
        Subsystem: Intel Corporation HD Audio Controller
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 22
        Region 0: Memory at ffa70000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [70] Express Unknown type IRQ 0
                Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
                Device: Latency L0s <64ns, L1 <1us
                Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
                Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
                Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
                Link: Latency L0s <64ns, L1 <1us
                Link: ASPM Disabled CommClk- ExtSynch-
                Link: Speed unknown, Width x0
        Capabilities: [100] Virtual Channel
        Capabilities: [130] Unknown (5)
00: 86 80 3e 29 06 00 10 00 02 00 03 04 08 00 00 00
10: 04 00 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 3e 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 07 01 00 00

00:1d.0 USB Controller: Intel Corporation USB UHCI Controller #1 (rev 02)
(prog-if 00 [UHCI])
        Subsystem: Intel Corporation USB UHCI Controller #1
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 23
        Region 4: I/O ports at d400 [size=32]
        Capabilities: [50] Vendor Specific Information
00: 86 80 34 29 05 00 90 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d4 00 00 00 00 00 00 00 00 00 00 86 80 34 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00

00:1d.1 USB Controller: Intel Corporation USB UHCI Controller #2 (rev 02)
(prog-if 00 [UHCI])
        Subsystem: Intel Corporation USB UHCI Controller #2
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 19
        Region 4: I/O ports at d080 [size=32]
        Capabilities: [50] Vendor Specific Information
00: 86 80 35 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 d0 00 00 00 00 00 00 00 00 00 00 86 80 35 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 03 02 00 00

00:1d.2 USB Controller: Intel Corporation USB UHCI Controller #3 (rev 02)
(prog-if 00 [UHCI])
        Subsystem: Intel Corporation USB UHCI Controller #3
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin D routed to IRQ 16
        Region 4: I/O ports at d000 [size=32]
        Capabilities: [50] Vendor Specific Information
00: 86 80 36 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d0 00 00 00 00 00 00 00 00 00 00 86 80 36 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 04 00 00

00:1d.7 USB Controller: Intel Corporation USB2 EHCI Controller #1 (rev 02)
(prog-if 20 [EHCI])
        Subsystem: Intel Corporation USB2 EHCI Controller #1
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 23
        Region 0: Memory at ffa7b000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Debug port
        Capabilities: [98] Vendor Specific Information
00: 86 80 3a 29 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 b0 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 3a 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) (prog-if 01
[Subtractive decode])
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
        Memory behind bridge: ff600000-ff6fffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
        Capabilities: [50] Subsystem: Intel Corporation 82801 PCI Bridge
00: 86 80 4e 24 06 01 10 00 92 01 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 20 f0 00 80 22
20: 60 ff 60 ff f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 02 00

00:1f.0 ISA bridge: Intel Corporation LPC Interface Controller (rev 02)
        Subsystem: Intel Corporation LPC Interface Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Capabilities: [e0] Vendor Specific Information
00: 86 80 10 29 07 00 10 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 10 29
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

00:1f.2 SATA controller: Intel Corporation 6 port SATA AHCI Controller (rev 02)
(prog-if 01 [AHCI 1.0])
        Subsystem: Intel Corporation 6 port SATA AHCI Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 319
        Region 0: I/O ports at cc00 [size=8]
        Region 1: I/O ports at c880 [size=4]
        Region 2: I/O ports at c800 [size=8]
        Region 3: I/O ports at c480 [size=4]
        Region 4: I/O ports at c400 [size=32]
        Region 5: Memory at ffa78800 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/4
Enable+
                Address: fee0300c  Data: 4169
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [a8] #12 [0010]
        Capabilities: [b0] Vendor Specific Information
00: 86 80 22 29 07 04 b0 02 02 01 06 01 00 00 00 00
10: 01 cc 00 00 81 c8 00 00 01 c8 00 00 81 c4 00 00
20: 01 c4 00 00 00 88 a7 ff 00 00 00 00 86 80 22 29
30: 00 00 00 00 80 00 00 00 00 00 00 00 03 02 00 00

00:1f.3 SMBus: Intel Corporation SMBus Controller (rev 02)
        Subsystem: Intel Corporation SMBus Controller
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin C routed to IRQ 18
        Region 0: Memory at ffa7b800 (64-bit, non-prefetchable) [size=256]
        Region 4: I/O ports at 0400 [size=32]
00: 86 80 30 29 03 00 80 02 02 00 05 0c 00 00 00 00
10: 04 b8 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 04 00 00 00 00 00 00 00 00 00 00 86 80 30 29
30: 00 00 00 00 00 00 00 00 00 00 00 00 03 03 00 00

00:1f.5 IDE interface: Intel Corporation 2 port SATA IDE Controller (rev 02)
(prog-if 85 [Master SecO PriO])
        Subsystem: Intel Corporation 2 port SATA IDE Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 19
        Region 0: I/O ports at c000 [size=8]
        Region 1: I/O ports at bc00 [size=4]
        Region 2: I/O ports at b880 [size=8]
        Region 3: I/O ports at b800 [size=4]
        Region 4: I/O ports at b480 [size=16]
        Region 5: I/O ports at b400 [size=16]
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [b0] Vendor Specific Information
00: 86 80 26 29 07 00 b0 02 02 85 01 01 00 00 00 00
10: 01 c0 00 00 01 bc 00 00 81 b8 00 00 01 b8 00 00
20: 81 b4 00 00 01 b4 00 00 00 00 00 00 86 80 26 29
30: 00 00 00 00 70 00 00 00 00 00 00 00 03 02 00 00

00:1f.6 Signal processing controller: Intel Corporation Thermal Subsystem (rev 02)
        Subsystem: Intel Corporation Thermal Subsystem
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Interrupt: pin C routed to IRQ 12
        Region 0: Memory at ffa6f000 (64-bit, non-prefetchable) [size=4K]
        Capabilities: [50] Power Management version 3
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 32 29 02 00 10 00 02 00 80 11 00 00 00 00
10: 04 f0 a6 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 32 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0c 03 00 00

01:00.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC
(rev 01)
        Subsystem: Wistron NeWeb Corp. CM9 Wireless a/b/g MiniPCI Adapter
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (2500ns min, 7000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 14
        Region 0: Memory at ff6f0000 (32-bit, non-prefetchable) [size=64K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00: 8c 16 13 00 16 00 90 02 01 00 00 02 08 40 00 00
10: 00 00 6f ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 01 50 00 00 5f 18 12 10
30: 00 00 00 00 44 00 00 00 00 00 00 00 0e 01 0a 1c



Should I try?

regards,
-- 
Jiri Slaby (jirislaby@gmail.com)
Faculty of Informatics, Masaryk University
-
Previous message: [thread] [date] [author]
Next message: [thread] [date] [author]
Messages in current thread:
2.6.23-rc6-mm1, Andrew Morton, (Tue Sep 18, 1:18 am)
Re: 2.6.23-rc6-mm1, Andrew Morton, (Tue Sep 18, 1:24 am)
Re: 2.6.23-rc6-mm1, Kamalesh Babulal, (Tue Sep 18, 2:13 am)
Re: 2.6.23-rc6-mm1, Andrew Morton, (Tue Sep 18, 2:27 am)
Re: 2.6.23-rc6-mm1, Andy Whitcroft, (Tue Sep 18, 2:34 am)
Re: 2.6.23-rc6-mm1, Satyam Sharma, (Tue Sep 18, 2:34 am)
Re: 2.6.23-rc6-mm1, Benjamin Herrenschmidt, (Tue Sep 18, 3:02 am)
Re: 2.6.23-rc6-mm1, Kamalesh Babulal, (Tue Sep 18, 5:07 am)
Re: 2.6.23-rc6-mm1, Valdis.Kletnieks, (Tue Sep 18, 8:07 am)
Re: 2.6.23-rc6-mm1, Miles Lane, (Tue Sep 18, 8:27 am)
Re: 2.6.23-rc6-mm1, Miles Lane, (Tue Sep 18, 8:39 am)
modpost errors ( Re: 2.6.23-rc6-mm1), Gabriel C, (Tue Sep 18, 8:43 am)
Re: 2.6.23-rc6-mm1, Sam Ravnborg, (Tue Sep 18, 8:50 am)
Re: 2.6.23-rc6-mm1, Sam Ravnborg, (Tue Sep 18, 8:52 am)
Re: modpost errors ( Re: 2.6.23-rc6-mm1), Sam Ravnborg, (Tue Sep 18, 8:56 am)
2.6.23-rc6-mm1: Build failure on ppc64 drivers/net/ehea/eh ..., Mel Gorman, (Tue Sep 18, 9:20 am)
Re: [v4l-dvb-maintainer] modpost errors ( Re: 2.6.23-rc6-mm1), mkrufky, (Tue Sep 18, 9:37 am)
Re: 2.6.23-rc6-mm1: Build failure on ppc64 drivers/net/ehe ..., Mel Gorman, (Tue Sep 18, 9:41 am)
Re: 2.6.23-rc6-mm1, Andrew Morton, (Tue Sep 18, 9:53 am)
Re: 2.6.23-rc6-mm1 (watchdog), Randy Dunlap, (Tue Sep 18, 10:18 am)
Re: 2.6.23-rc6-mm1, Miles Lane, (Tue Sep 18, 10:20 am)
Re: 2.6.23-rc6-mm1 (watchdog), Randy Dunlap, (Tue Sep 18, 10:41 am)
Re: 2.6.23-rc6-mm1, Mel Gorman, (Tue Sep 18, 10:44 am)
Re: 2.6.23-rc6-mm1, Mel Gorman, (Tue Sep 18, 11:05 am)
Re: 2.6.23-rc6-mm1: Build failure on ppc64 drivers/net/ehe ..., David Miller, (Tue Sep 18, 12:08 pm)
Re: 2.6.23-rc6-mm1, Greg KH, (Tue Sep 18, 12:16 pm)
Re: 2.6.23-rc6-mm1, Greg KH, (Tue Sep 18, 12:17 pm)
Re: 2.6.23-rc6-mm1, Sam Ravnborg, (Tue Sep 18, 12:17 pm)
2.6.23-rc6-mm1 - Mostly working, with a kbuild oddity, Valdis.Kletnieks, (Tue Sep 18, 12:32 pm)
Re: 2.6.23-rc6-mm1, Miles Lane, (Tue Sep 18, 12:42 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, Rafael J. Wysocki, (Tue Sep 18, 1:21 pm)
Re: 2.6.23-rc6-mm1, Sam Ravnborg, (Tue Sep 18, 1:26 pm)
Re: 2.6.23-rc6-mm1 - Mostly working, with a kbuild oddity, Sam Ravnborg, (Tue Sep 18, 1:32 pm)
Re: 2.6.23-rc6-mm1 sparc build error, Mathieu Desnoyers, (Tue Sep 18, 1:54 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, Rafael J. Wysocki, (Tue Sep 18, 1:54 pm)
Re: 2.6.23-rc6-mm1 sparc build error, Andrew Morton, (Tue Sep 18, 2:05 pm)
Re: 2.6.23-rc6-mm1, Benjamin Herrenschmidt, (Tue Sep 18, 2:35 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Tue Sep 18, 2:37 pm)
Re: 2.6.23-rc6-mm1: atomic counter underflow, Mariusz Kozlowski, (Tue Sep 18, 2:45 pm)
Re: 2.6.23-rc6-mm1 - Mostly working, with a kbuild oddity, Valdis.Kletnieks, (Tue Sep 18, 3:03 pm)
Re: [v4l-dvb-maintainer] modpost errors ( Re: 2.6.23-rc6-mm1), Mauro Carvalho Chehab, (Tue Sep 18, 3:06 pm)
Re: 2.6.23-rc6-mm1, Gabriel C, (Tue Sep 18, 3:38 pm)
Re: 2.6.23-rc6-mm1, Gabriel C, (Tue Sep 18, 3:48 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Wed Sep 19, 12:06 am)
Re: 2.6.23-rc6-mm1 - Mostly working, with a kbuild oddity, Sam Ravnborg, (Wed Sep 19, 12:34 am)
Re: 2.6.23-rc6-mm1: atomic counter underflow, Cornelia Huck, (Wed Sep 19, 1:27 am)
2.6.23-rc6-mm1 -- powerpc link failure, Andy Whitcroft, (Wed Sep 19, 2:28 am)
2.6.23-rc6-mm1 -- powerpc pSeries_log_error panic in rtas_ ..., Andy Whitcroft, (Wed Sep 19, 2:36 am)
X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Wed Sep 19, 4:43 am)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Wed Sep 19, 4:53 am)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Wed Sep 19, 7:59 am)
Re: 2.6.23-rc6-mm1 - Mostly working, with a kbuild oddity, Valdis.Kletnieks, (Wed Sep 19, 8:53 am)
2.6.23-rc6-mm1: kgdb support on ppc64 utterly broken, Mel Gorman, (Wed Sep 19, 9:29 am)
Re: 2.6.23-rc6-mm1 -- powerpc link failure, Segher Boessenkool, (Wed Sep 19, 9:36 am)
2.6.23-rc6-mm1 -- mkfs stuck in 'D', Andy Whitcroft, (Wed Sep 19, 9:43 am)
Re: 2.6.23-rc6-mm1: atomic counter underflow, Mariusz Kozlowski, (Wed Sep 19, 9:43 am)
Re: 2.6.23-rc6-mm1 -- powerpc link failure, Andy Whitcroft, (Wed Sep 19, 9:52 am)
Re: 2.6.23-rc6-mm1 - Mostly working, with a kbuild oddity, Sam Ravnborg, (Wed Sep 19, 10:39 am)
Re: 2.6.23-rc6-mm1 -- powerpc link failure, Sam Ravnborg, (Wed Sep 19, 10:44 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Wed Sep 19, 10:44 am)
Re: 2.6.23-rc6-mm1: atomic counter underflow, Cornelia Huck, (Wed Sep 19, 11:02 am)
Re: 2.6.23-rc6-mm1, Sam Ravnborg, (Wed Sep 19, 11:48 am)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Andrew Morton, (Wed Sep 19, 12:10 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Wed Sep 19, 12:21 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Andi Kleen, (Wed Sep 19, 12:24 pm)
Re: 2.6.23-rc6-mm1, Sam Ravnborg, (Wed Sep 19, 12:33 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Wed Sep 19, 12:46 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Andi Kleen, (Wed Sep 19, 12:54 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Wed Sep 19, 12:57 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Wed Sep 19, 1:01 pm)
Re: 2.6.23-rc6-mm1 -- mkfs stuck in 'D', Hugh Dickins, (Wed Sep 19, 1:03 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Valdis.Kletnieks, (Wed Sep 19, 1:32 pm)
Re: 2.6.23-rc6-mm1, Gabriel C, (Wed Sep 19, 1:36 pm)
Re: 2.6.23-rc6-mm1, Sam Ravnborg, (Wed Sep 19, 1:43 pm)
Re: 2.6.23-rc6-mm1 -- mkfs stuck in 'D', Peter Zijlstra, (Wed Sep 19, 1:44 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Wed Sep 19, 1:47 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Andrew Morton, (Wed Sep 19, 2:42 pm)
Re: 2.6.23-rc6-mm1, Tilman Schmidt, (Wed Sep 19, 4:02 pm)
Re: 2.6.23-rc6-mm1, Andrew Morton, (Wed Sep 19, 4:24 pm)
Re: 2.6.23-rc6-mm1, Chuck Ebbert, (Wed Sep 19, 4:28 pm)
Re: 2.6.23-rc6-mm1, David Brownell, (Wed Sep 19, 4:44 pm)
Re: 2.6.23-rc6-mm1, Tilman Schmidt, (Wed Sep 19, 4:55 pm)
Re: 2.6.23-rc6-mm1, Joseph Fannin, (Wed Sep 19, 4:58 pm)
Re: 2.6.23-rc6-mm1, Andrew Morton, (Wed Sep 19, 5:06 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Wed Sep 19, 5:06 pm)
Re: 2.6.23-rc6-mm1, Andrew Morton, (Wed Sep 19, 5:09 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Dave Airlie, (Wed Sep 19, 5:18 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Dave Airlie, (Wed Sep 19, 6:42 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Dave Airlie, (Wed Sep 19, 6:51 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Andrew Morton, (Wed Sep 19, 7:24 pm)
Re: 2.6.23-rc6-mm1, David Brownell, (Wed Sep 19, 9:43 pm)
Re: 2.6.23-rc6-mm1, Andrew Morton, (Wed Sep 19, 11:11 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Wed Sep 19, 11:18 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Thu Sep 20, 12:19 am)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Thu Sep 20, 12:24 am)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Dave Airlie, (Thu Sep 20, 12:33 am)
kobject: Temporarily save k_name on cleanup for debug message., Cornelia Huck, (Thu Sep 20, 12:42 am)
kobject: Temporarily save k_name on cleanup for debug message., Cornelia Huck, (Thu Sep 20, 12:43 am)
Re: 2.6.23-rc6-mm1, Kay Sievers, (Thu Sep 20, 12:54 am)
Re: 2.6.23-rc6-mm1 - make access to tasks nsproxy ligther ..., Cedric Le Goater, (Thu Sep 20, 1:41 am)
Re: 2.6.23-rc6-mm1, Alessandro Zummo, (Thu Sep 20, 1:51 am)
Re: 2.6.23-rc6-mm1 - make access to tasks nsproxy ligther ..., Pavel Emelyanov, (Thu Sep 20, 1:59 am)
Re: 2.6.23-rc6-mm1 - make access to tasks nsproxy ligther ..., Cedric Le Goater, (Thu Sep 20, 2:12 am)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Zhenyu Wang, (Thu Sep 20, 2:24 am)
Re: 2.6.23-rc6-mm1 -- mkfs stuck in 'D', Hugh Dickins, (Thu Sep 20, 4:31 am)
Re: 2.6.23-rc6-mm1 -- mkfs stuck in 'D', Peter Zijlstra, (Thu Sep 20, 5:15 am)
Re: 2.6.23-rc6-mm1 sparc build error, Guennadi Liakhovetski, (Thu Sep 20, 5:53 am)
2.6.23-rc6-mm1: Build failure on ppc64 drivers/ata/pata_scc.c, Mel Gorman, (Thu Sep 20, 6:13 am)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Valdis.Kletnieks, (Thu Sep 20, 6:17 am)
Build failure on ppc64 drivers/block/ps3disk.c, Mel Gorman, (Thu Sep 20, 6:25 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Thu Sep 20, 6:29 am)
Re: Build failure on ppc64 drivers/block/ps3disk.c, Jens Axboe, (Thu Sep 20, 6:32 am)
Re: 2.6.23-rc6-mm1: atomic counter underflow, Cornelia Huck, (Thu Sep 20, 6:35 am)
2.6.23-rc6-mm1: Build failures on ppc64_defconfig, Satyam Sharma, (Thu Sep 20, 6:37 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Thu Sep 20, 6:43 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Thu Sep 20, 6:53 am)
Re: 2.6.23-rc6-mm1: Build failure on ppc64 drivers/ata/pat ..., Alan Cox, (Thu Sep 20, 7:09 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Thu Sep 20, 7:12 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Thu Sep 20, 7:47 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Thu Sep 20, 7:50 am)
Re: 2.6.23-rc6-mm1: Build failure on ppc64 drivers/ata/pat ..., Mel Gorman, (Thu Sep 20, 8:14 am)
Re: 2.6.23-rc6-mm1: Build failure on ppc64 drivers/ata/pat ..., Kamalesh Babulal, (Thu Sep 20, 8:45 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Thu Sep 20, 8:49 am)
Re: 2.6.23-rc6-mm1, David Brownell, (Thu Sep 20, 9:15 am)
Re: 2.6.23-rc6-mm1: atomic counter underflow, Pierre Ossman, (Thu Sep 20, 9:30 am)
Re: 2.6.23-rc6-mm1 - make access to tasks nsproxy ligther ..., Cedric Le Goater, (Thu Sep 20, 10:08 am)
Re: kobject: Temporarily save k_name on cleanup for debug ..., Mariusz Kozlowski, (Thu Sep 20, 10:26 am)
Re: 2.6.23-rc6-mm1: atomic counter underflow, Mariusz Kozlowski, (Thu Sep 20, 10:27 am)
Re: 2.6.23-rc6-mm1, David Brownell, (Thu Sep 20, 10:36 am)
Re: 2.6.23-rc6-mm1, Tilman Schmidt, (Thu Sep 20, 12:10 pm)
Re: 2.6.23-rc6-mm1, Tilman Schmidt, (Thu Sep 20, 12:20 pm)
Re: 2.6.23-rc6-mm1, Andrew Morton, (Thu Sep 20, 1:25 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Thu Sep 20, 1:39 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Thu Sep 20, 1:42 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Thu Sep 20, 2:08 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Linus Torvalds, (Thu Sep 20, 2:35 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Thu Sep 20, 2:45 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Thu Sep 20, 2:53 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Thu Sep 20, 2:54 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Linus Torvalds, (Thu Sep 20, 2:55 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Thu Sep 20, 3:01 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Thu Sep 20, 3:05 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Matt Mackall, (Thu Sep 20, 3:06 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Thu Sep 20, 3:10 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Dave Airlie, (Thu Sep 20, 3:24 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Thu Sep 20, 3:30 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Thu Sep 20, 3:35 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Andi Kleen, (Thu Sep 20, 4:03 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Matt Mackall, (Thu Sep 20, 4:31 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Len Brown, (Thu Sep 20, 4:35 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Andi Kleen, (Thu Sep 20, 4:44 pm)
Re: 2.6.23-rc6-mm1, Tilman Schmidt, (Thu Sep 20, 5:53 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Zhenyu Wang, (Thu Sep 20, 6:27 pm)
[PATCH] Remove broken netfilter binary sysctls from bridgi ..., Joseph Fannin, (Thu Sep 20, 7:05 pm)
Re: [PATCH] Remove broken netfilter binary sysctls from br ..., Eric W. Biederman, (Thu Sep 20, 9:21 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Paul Mackerras, (Thu Sep 20, 9:51 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Fri Sep 21, 12:07 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Fri Sep 21, 12:56 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Fri Sep 21, 1:06 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Fri Sep 21, 2:24 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Fri Sep 21, 2:25 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Fri Sep 21, 5:59 am)
Re: 2.6.23-rc6-mm1 sparc build error, Mathieu Desnoyers, (Fri Sep 21, 6:51 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Fri Sep 21, 7:20 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Fri Sep 21, 9:27 am)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Valdis.Kletnieks, (Fri Sep 21, 10:16 am)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Valdis.Kletnieks, (Fri Sep 21, 10:18 am)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Fri Sep 21, 10:30 am)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Valdis.Kletnieks, (Fri Sep 21, 10:54 am)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Thomas Gleixner, (Fri Sep 21, 12:16 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Fri Sep 21, 12:20 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Valdis.Kletnieks, (Fri Sep 21, 12:33 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Rafael J. Wysocki, (Fri Sep 21, 12:37 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Fri Sep 21, 12:38 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Fri Sep 21, 12:43 pm)
Re: 2.6.23-rc6-mm1 -- mkfs stuck in 'D', Fengguang Wu, (Fri Sep 21, 6:55 pm)
Re: 2.6.23-rc6-mm1: Build failure on ppc64 drivers/ata/pat ..., Satyam Sharma, (Fri Sep 21, 7:50 pm)
Re: 2.6.23-rc6-mm1: Build failures on ppc64_defconfig, Satyam Sharma, (Fri Sep 21, 11:50 pm)
Re: 2.6.23-rc6-mm1: Build failures on ppc64_defconfig, Satyam Sharma, (Fri Sep 21, 11:51 pm)
Re: 2.6.23-rc6-mm1: Build failures on ppc64_defconfig, Satyam Sharma, (Fri Sep 21, 11:54 pm)
Re: 2.6.23-rc6-mm1: Build failures on ppc64_defconfig, Satyam Sharma, (Sat Sep 22, 12:25 am)
[PATCH -mm] pasemi_mac: Build fix after recent netdev stat ..., Satyam Sharma, (Sat Sep 22, 12:40 am)
[PATCH -mm] mv643xx_eth: Remove redundant multiple initial ..., Satyam Sharma, (Sat Sep 22, 12:54 am)
[PATCH -mm] iseries_veth: Kill unused variable, Satyam Sharma, (Sat Sep 22, 12:55 am)
Re: 2.6.23-rc6-mm1, Satyam Sharma, (Sat Sep 22, 1:41 am)
Re: 2.6.23-rc6-mm1, Satyam Sharma, (Sat Sep 22, 2:21 am)
Re: 2.6.23-rc6-mm1 -- mkfs stuck in 'D', Peter Zijlstra, (Sat Sep 22, 6:16 am)
Re: 2.6.23-rc6-mm1 -- mkfs stuck in 'D', Fengguang Wu, (Sat Sep 22, 6:20 pm)
[BUG 2.6.23-rc6-mm1] NMI Watchdog detected LOCKUP on CPU 0, Fengguang Wu, (Sat Sep 22, 6:42 pm)
[-mm Patch] net/bluetooth/hidp/core.c: Make hidp_setup_inp ..., WANG Cong, (Sat Sep 22, 8:01 pm)
Re: [BUG 2.6.23-rc6-mm1] NMI Watchdog detected LOCKUP on CPU 0, Andrew Morton, (Sat Sep 22, 9:22 pm)
Re: [BUG 2.6.23-rc6-mm1] NMI Watchdog detected LOCKUP on CPU 0, Fengguang Wu, (Sat Sep 22, 10:30 pm)
Re: [BUG 2.6.23-rc6-mm1] NMI Watchdog detected LOCKUP on CPU 0, Andrew Morton, (Sat Sep 22, 10:35 pm)
Re: [BUG 2.6.23-rc6-mm1] NMI Watchdog detected LOCKUP on CPU 0, Fengguang Wu, (Sat Sep 22, 10:53 pm)
Re: 2.6.23-rc6-mm1 -- mkfs stuck in 'D', Peter Zijlstra, (Sun Sep 23, 6:02 am)
Re: 2.6.23-rc6-mm1 -- ipg.c don't compile on i386 with CON ..., trem, (Sun Sep 23, 7:19 am)
Re: [-mm Patch] net/bluetooth/hidp/core.c: Make hidp_setup ..., roel, (Sun Sep 23, 3:13 pm)
Re: [-mm Patch] net/bluetooth/hidp/core.c: Make hidp_setup ..., WANG Cong, (Sun Sep 23, 7:38 pm)
[Resend][-mm Patch] net/bluetooth/hidp/core.c: Make hidp_s ..., WANG Cong, (Sun Sep 23, 7:50 pm)
Re: 2.6.23-rc6-mm1 -- mkfs stuck in 'D', Fengguang Wu, (Sun Sep 23, 8:01 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Valdis.Kletnieks, (Sun Sep 23, 8:25 pm)
Re: 2.6.23-rc6-mm1 - make access to tasks nsproxy ligther ..., Serge E. Hallyn, (Sun Sep 23, 9:00 pm)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Sun Sep 23, 11:06 pm)
Re: [-mm Patch] net/bluetooth/hidp/core.c: Make hidp_setup ..., Marcel Holtmann, (Mon Sep 24, 12:09 am)
Re: 2.6.23-rc6-mm1 -- mkfs stuck in 'D', Peter Zijlstra, (Mon Sep 24, 12:35 am)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Valdis.Kletnieks, (Mon Sep 24, 12:37 am)
Re: X-freeze after clflush changes [Was: 2.6.23-rc6-mm1], Jiri Slaby, (Mon Sep 24, 1:10 am)
Re: 2.6.23-rc6-mm1 -- mkfs stuck in 'D', Fengguang Wu, (Mon Sep 24, 1:12 am)
Re: 2.6.23-rc6-mm1: Build failure on ppc64 drivers/ata/pat ..., Mel Gorman, (Mon Sep 24, 4:01 am)
Re: 2.6.23-rc6-mm1: Build failures on ppc64_defconfig, Mel Gorman, (Mon Sep 24, 4:12 am)
Re: 2.6.23-rc6-mm1, Mel Gorman, (Mon Sep 24, 4:14 am)
Re: [PATCH] Remove broken netfilter binary sysctls from br ..., Patrick McHardy, (Mon Sep 24, 9:55 am)
Re: [PATCH] Remove broken netfilter binary sysctls from br ..., Stephen Hemminger, (Mon Sep 24, 1:14 pm)
Re: [PATCH] Remove broken netfilter binary sysctls from br ..., Patrick McHardy, (Mon Sep 24, 9:07 pm)
Re: 2.6.23-rc6-mm1, Greg KH, (Mon Sep 24, 10:35 pm)
Re: 2.6.23-rc6-mm1 -- powerpc link failure, Andy Whitcroft, (Tue Sep 25, 6:40 am)
Re: [PATCH] Remove broken netfilter binary sysctls from br ..., Eric W. Biederman, (Tue Sep 25, 7:03 am)
Re: [PATCH] Remove broken netfilter binary sysctls from br ..., Patrick McHardy, (Tue Sep 25, 7:26 am)
Re: [PATCH] Remove broken netfilter binary sysctls from br ..., Stephen Hemminger, (Tue Sep 25, 9:12 am)
Re: [PATCH] Remove broken netfilter binary sysctls from br ..., Patrick McHardy, (Tue Sep 25, 9:22 am)
Re: [PATCH] Remove broken netfilter binary sysctls from br ..., Eric W. Biederman, (Tue Sep 25, 9:38 am)
Re: 2.6.23-rc6-mm1: Build failure on ppc64 drivers/ata/pat ..., Jeff Garzik, (Tue Sep 25, 8:39 pm)
Re: 2.6.23-rc6-mm1: failure to boot on HP nx6325, no sound ..., Pavel Machek, (Thu Oct 11, 2:19 pm)