> Hi,
>
> this issue has been already discussed on the kernelnewbies mailing list
> [1],[2] and suggested to be further discussed here.
>
> I am currently working on a MPC8540-based custom board, which runs Linux
> 2.6.15 (arch/ppc). The original Linux sources have been modified to
> support that custom board. (Additional patches to support LTT are
> applied as well, though disabled in the running kernel)
>
> I set up a periodically running kernel thread, which is delayed for a
> single jiffy using schedule_timeout() in an infinite loop. It is used to
> measure delays between invocations of that thread. For measuring the
> distance in time the PPC's time base lower half register is used
> (obtained using get_cycles() defined in asm/timex.h).
>
> The thread calculates the delay to the previous run and only outputs the
> result if a new maximum value has been determined (in respect to all
> previous cycles). Further the thread outputs a warning if a very "high"
> delay was determined. I.e. a delay greater than 5ms.
>
> While running that test driver a delay of about 10ms _exactly_ occurs
> every 10 minutes.
>
> The kernel is configured using CONFIG_HZ=1000 and CONFIG_PREEMPT.
> The CCB is at 333MHz, whereas the TBR update rate is 333 MHz / 8, i.e.
> 41,625 MHz.
> Kernel configuration as a whole is found here:
>
http://nopaste.info/5e4d0283bb.html
>
> And now the funny part starts.
> I got a response from Bruce Rowen on kernelnewbies, telling me that he
> came across the same problem. He increased his AMD-Geode-based platform
> to 1GB of RAM (256MB before) and also hit the 10-minutes-issue a few
> month ago (using Linux 2.6.13).
> Going back to 256MB cured the problem. I did the same thing by
> instructing the boot loader in order to only use 256 MB of RAM (instead
> of 512MB) and yes, the 10-minutes-issue was gone as well.
>
> Apart of some kernel threads almost all user processes have been killed
> during the test. Only SSH and a bash were running (whereas a test with
> network interfaces completely disabled and only operated from a serial
> console turned out the same results).
> The kernel comes with compiled in CIFS support, some kernel debugging
> features like soft-lockup detection and preemption debugging. I.e. ps
> lists the kernel threads ksoftirqd, watchdog, events, khelper, kthread,
> kblockd, pdflush, aio, cifsoplockd and cifsdnotifyd.
>
> An appropriate userspace test tool based on nanosleep() determined the
> same results like the kernel thread:
>
> root@mpc0:/# /tmp/wait.rt
> looping 1 milli seconds nanosleep ...
> 15:26:16: #1 FRAME MAX 1996 us (at 4139773004 ticks)
> 15:26:16: #2 FRAME MAX 2002 us (at 4139856360 ticks)
> 15:26:16: #155 FRAME MAX 2102 us (at 4152597854 ticks)
> 15:41:37: #460398 FRAME MAX 8941 us (at 3813406605 ticks)
> 15:41:37: #460398 FRAME HIGH 8941 us (at 3813406605 ticks)
> 15:51:37: #760394 FRAME MAX 9936 us (at 3018602602 ticks)
> 15:51:37: #760394 FRAME HIGH 9936 us (at 3018602602 ticks)
> 16:01:37: #1060390 FRAME HIGH 9935 us (at 2223798809 ticks)
> 16:11:37: #1360386 FRAME HIGH 9934 us (at 1428994989 ticks)
> 16:21:37: #1660382 FRAME HIGH 9935 us (at 634191241 ticks)
> [...]
