Στις 26 Νοεμβρίου 2010 2:54 π.μ., ο χρήστης Jonathan Guerin
<jonathan@guerin.id.au> έγραψε:
quoted text
> On Thu, Nov 25, 2010 at 8:41 AM, Jonathan Guerin <jonathan@guerin.id.au> wrote:
>> On Wed, Nov 24, 2010 at 10:55 PM, Nick Kossifidis <mickflemm@gmail.com> wrote:
>>> 2010/11/24 Jonathan Guerin <jonathan@guerin.id.au>:
>>>>
>>>>> diff --git a/drivers/net/wireless/ath/ath5k/pcu.c b/drivers/net/wireless/ath/ath5k/pcu.c
>>>>> index e691378..4556f29 100644
>>>>> --- a/drivers/net/wireless/ath/ath5k/pcu.c
>>>>> +++ b/drivers/net/wireless/ath/ath5k/pcu.c
>>>>> @@ -763,7 +763,7 @@ ath5k_hw_check_beacon_timers(struct ath5k_hw *ah, int intval)
>>>>>  * @ah: The &struct ath5k_hw
>>>>>  * @coverage_class: IEEE 802.11 coverage class number
>>>>>  *
>>>>> - * Sets slot time, ACK timeout and CTS timeout for given coverage class.
>>>>> + * Sets IFS intervals and ACK/CTS timeouts for given coverage class.
>>>>>  */
>>>>>  void ath5k_hw_set_coverage_class(struct ath5k_hw *ah, u8 coverage_class)
>>>>>  {
>>>>> @@ -772,7 +772,7 @@ void ath5k_hw_set_coverage_class(struct ath5k_hw *ah, u8 coverage_class)
>>>>>        int ack_timeout = ath5k_hw_get_default_sifs(ah) + slot_time;
>>>>
>>>> This is not quite right:
>>>>
>>>> According to the 802.11-2007 spec document, the ACKTimeout value is
>>>> (Section 9.2.8 ACK procedure):
>>>> ACKTimeout = aSIFSTime + aSlotTime + aPHY-RX-START-Delay
>>>>
>>>> From Table 17-15--OFDM PHY characteristics, the values are:
>>>> aSIFSTime = 16
>>>> aSlotTime = 9
>>>> aPHY-RX-START-Delay = 25
>>>>
>>>> Therefore, ACKTimeout = 50
>>>>
>>>> Ignoring my uniformed comments from before, this is the only thing I
>>>> can see that's wrong.
>>>>
>>>> Cheers,
>>>>
>>>> Jonathan
>>>
>>> Hmm I didn't mess with set_coverage_class so i didn't look up for ack
>>> timeout. That phy-rx-start-delay is standard value or hw specific ?
>>> Also does it change with clockrate (bwmodes) ? We already have a phy
>>> activation -> rx start delay (check patch 25). It's 10.000 on RF5111
>>> and 2.000 on RF5112 and later, if we divide by A clock it's 250 on
>>> RF5111 and 50 on RF5112 and later. Do you think it's related ?
>>
>> The phy-rx-start-delay is set in the standard. I'll find you the
>> relevant pages soon.
>
> The aPHY-RX-START-Delay value is specific per PHY. In the case of
> OFDM, you can find the relevant timings at:
>
> Table 17-15--OFDM PHY characteristics
> aPHY-RX-START-Delay 25 μs (20MHz) 49 μs (10MHz) 97 μs (5MHz)
>
>>
>> I'll look up the others tomorrow. I'm feeling pretty sick today, so
>> not sure if I'll get a chance.
>
> I just a quick look at the code. The first thing that pops to mind and
> that is apparent in the Table mentioned above, you can't just multiply
> by 2 every time you halve the channel - the value is actually slightly
> shorter than this.
>

When we convert to core clock units it's what we should do, all
timings should change the same way. I don't know what this
aPHY-RX-START-Delay is but if it changes that way we can use absolute
values as we do for slot time and sifs. Maybe we can add a function
ath5k_hw_get_default_ack_timeout that gets default sifs + default slot
time + the needed aPHY-RX-START-Delay based on the standard (but what
about turbo mode -40MHz-, do you think that using a value of 25/2
would be ok ?) and returns the total ack timeout in usecs. Or we can
do that on set_coverage_class (I prefer the first option).

quoted text
> Secondly, I'm assuming that the AR5K_PHY_RX_DELAY register refers to
> the aPHY-RX-START-Delay value from the standard. It would make sense
> that the card require this value, as it is necessary in resetting the
> NAV (9.2.5.4 Setting and resetting the NAV), for CTS timeouts (9.2.5.7
> CTS procedure), & ACK Timeouts (9.2.8 ACK procedure). The first 2
> cases both refer to station behaviour after an RTS frame, but are
> slightly different in that one is from an overhearing station, whereas
> the the second is from the sending station. In the driver, which case
> is the CTSTimeout value used for?
>
> Cheers,
>
> Jonathan
>

I just remembered that this register value is in /100ns units
(according to what we have so far -check comments, remember, no
documentation on PHY registers-) so 10000 * 100ns = 1000us = 1ms for
RF5111 and 2000 * 100ns = 200us = 0.2ms for RF5112+ So it can't be
related. If it was related we (and HAL) would write this back on hw
for different bwmodes.


-- 
GPG ID: 0xD21DB2DB
As you read this post global entropy rises. Have Fun ;-)
Nick
_______________________________________________
ath5k-devel mailing list
ath5k-devel@lists.ath5k.org
https://lists.ath5k.org/mailman/listinfo/ath5k-devel